Wellcraft V20 Community

Go Back   Wellcraft V20 Community > Wellcraft V-20 Forums > General
Register FAQ Community Calendar Today's Posts Search

Reply
Thread Tools Display Modes
  #11  
Unread 12-31-2012, 09:50 AM
jasoncooperpcola's Avatar
jasoncooperpcola jasoncooperpcola is offline
God
 
Join Date: May 2007
Location: Pensacola, FL
Posts: 1,467
Send a message via Yahoo to jasoncooperpcola
Default

Tether the stern to a solid anchor point. Pull the trailer out with your tow vehicle about two foot. Block the stern up and pull the trailer out about 3/4 of the way. Now jack it off the trailer and block it and pull your trailer on out.
__________________
1983 V-20 capsized. . . . in the garage.
Reply With Quote
  #12  
Unread 12-31-2012, 11:44 AM
smokeonthewater's Avatar
smokeonthewater smokeonthewater is offline
God
 
Join Date: Oct 2011
Location: Indiana near louisville Ky
Posts: 1,814
Default

a hammer drill and a tapcon can make for a solid anchor point in concrete in short order
Reply With Quote
  #13  
Unread 12-31-2012, 02:35 PM
cfelton cfelton is offline
God
 
Join Date: Dec 2006
Location: Hobbsville, North Carolina
Posts: 1,364
Default

Its not too bad. I did it about like bksah2. Blocked up the keel and the chines on the stern and the keel about middle way down the hull and pulled the trailer out by hand.
__________________


77 V20 cuddy with 170 I/O Mercruiser
72 16ft. Carolina w/a 25hp Evinrude
Reply With Quote
  #14  
Unread 12-31-2012, 03:47 PM
garagenc's Avatar
garagenc garagenc is offline
God
 
Join Date: Sep 2006
Location: Camden NC
Posts: 1,782
Default

Go back to my thread when I replaced my inbd. I have truss's and what I did was put a 2x4 on either side of the bottom (horizontial) part of the truss and then put a vertical brace on either side of the boat from the floor to the bottom of the truss, lifted my 350 out with no trouble and I bet it would have lifted the boat eng and all.
Do a search under me or "repowering" I have pics of the whole thing and some close up of my bracing.
__________________
Tis better to be quiet and thought a fool than open your mouth and prove it!!

1991 V-20 cuddy I/O 350 volvo duo prop, 1998 15ft Grumman 9.9 Johnson

Last edited by garagenc; 12-31-2012 at 04:11 PM.
Reply With Quote
  #15  
Unread 12-31-2012, 05:59 PM
Destroyer's Avatar
Destroyer Destroyer is offline
God
 
Join Date: Apr 2010
Location: Montville, NJ
Posts: 8,236
Default

Quote:
Originally Posted by jasoncooperpcola View Post
Tether the stern to a solid anchor point. Pull the trailer out with your tow vehicle about two foot. Block the stern up and pull the trailer out about 3/4 of the way. Now jack it off the trailer and block it and pull your trailer on out.
That's exactly how I do it. Done it several times that way... works like a charm. (Although, now that I have a 2 1/2 bay garage, I'm liking Skools method of hanging it a lot).
__________________
1987 V20 w/1987 150HP Yamaha on a Shoreland'r Trailer
1978 16.5 Airslot w/1996 120HP Force on a Four Winns trailer
1996 V21 w/1993 200HP Mercury on a Shoreline Trailer
All towed by a 5.7L Hemi Durango.


If God didn't have a purpose for us we wouldn't be here, so
Live simply, Love generously, Care deeply, Speak kindly.
(Leave the rest to God)

Silence, in the face of evil, is itself evil. Not to speak is to speak, not to act is to act. God will not hold us guiltless.
Reply With Quote
  #16  
Unread 12-31-2012, 09:24 PM
aussie's Avatar
aussie aussie is offline
Senior Member
 
Join Date: Feb 2011
Location: rockbank australia
Posts: 562
Send a message via AIM to aussie Send a message via MSN to aussie Send a message via Skype™ to aussie
Default

same here i was going to do it out side but now that i seen it done im doing it in my garage give me time and comfort to get all that paint of the bottom here is some pics of the room i have to do it and i have a large beam there to hook up the *** end dont no why i didnt think of it before
Reply With Quote
  #17  
Unread 12-31-2012, 09:24 PM
aussie's Avatar
aussie aussie is offline
Senior Member
 
Join Date: Feb 2011
Location: rockbank australia
Posts: 562
Send a message via AIM to aussie Send a message via MSN to aussie Send a message via Skype™ to aussie
Default

Reply With Quote
  #18  
Unread 12-31-2012, 09:25 PM
aussie's Avatar
aussie aussie is offline
Senior Member
 
Join Date: Feb 2011
Location: rockbank australia
Posts: 562
Send a message via AIM to aussie Send a message via MSN to aussie Send a message via Skype™ to aussie
Default

Reply With Quote
  #19  
Unread 01-01-2013, 07:19 AM
jasoncooperpcola's Avatar
jasoncooperpcola jasoncooperpcola is offline
God
 
Join Date: May 2007
Location: Pensacola, FL
Posts: 1,467
Send a message via Yahoo to jasoncooperpcola
Default

Quote:
Originally Posted by Destroyer View Post
That's exactly how I do it. Done it several times that way... works like a charm. (Although, now that I have a 2 1/2 bay garage, I'm liking Skools method of hanging it a lot).
I like Skools idea too. But my garage is lucky to support itself, much less a V20. I am kicking myself for not replacing my rotted 4x4 roof supports and poles with a 3-layered 2x12 beam. When I roll the V out to flip it upright again I might upgrade my roof supports.
__________________
1983 V-20 capsized. . . . in the garage.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:43 AM.


Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.