Forum: Classifieds
05-07-2020, 08:59 PM
|
|
Replies: 1
Views: 605
|
|
Forum: Classifieds
05-06-2020, 04:29 PM
|
|
Replies: 1
Views: 605
1975 Wellcraft V20 for sale
$3,500 firm
1975 Wellcraft V20, runs great, looking to get a bigger boat. I had a lot done to this boat in the 6 years I had her.
- New transom, completely rebuilt 1995 Evinrude 150HP Ocean Pro ...
|
|
Forum: Boats For Sale or Wanted
05-06-2020, 07:27 AM
|
|
Replies: 0
Views: 272
1975 Wellcraft for sale
$3,500 firm
1975 Wellcraft V20, runs great, looking to get a bigger boat. I had a lot done to this boat in the 6 years I had her.
- New transom, completely rebuilt 1995 Evinrude 150HP Ocean Pro ...
|
|
Forum: Modifications
07-11-2017, 05:37 AM
|
|
Replies: 0
Views: 257
bow rail
Are there any other boat manufacturers who's bow rail will fit a 75' V20?
|
|
Forum: General
07-09-2017, 09:21 PM
|
|
Replies: 3
Views: 237
|
|
Forum: General
07-06-2017, 06:24 AM
|
|
Replies: 3
Views: 237
Bow rail
Are there any other boat manufacturers who's bow rail will fit a 75' V20?
|
|
Forum: General
07-09-2016, 06:21 AM
|
|
Replies: 9
Views: 331
|
|
Forum: General
07-09-2016, 06:11 AM
|
|
Replies: 9
Views: 331
Fuel fill vent
I have a 75 v20 with 20 gall. saddle tanks, I am getting water in my fuel vent in rough conditions. any suggestions on how to correct the problem. FYI when I redid my tanks I mounted vents with the...
|
|
Forum: General
10-20-2013, 06:37 AM
|
|
Replies: 34
Views: 1,115
|
|
Forum: General
10-19-2013, 10:15 PM
|
|
Replies: 34
Views: 1,115
|
|
Forum: General
10-19-2013, 06:19 AM
|
|
Replies: 34
Views: 1,115
|
|
Forum: General
10-18-2013, 03:41 PM
|
|
Replies: 34
Views: 1,115
I found a 7 - 1/2' 11 gauge piece of 3 X 4 tube...
I found a 7 - 1/2' 11 gauge piece of 3 X 4 tube steel new for $50 from a friends large truck repair shop. It will not be gal but I think it is ok, I will paint it up as it should never get saltwater...
|
|
Forum: General
10-17-2013, 04:24 PM
|
|
Replies: 34
Views: 1,115
|
|
Forum: General
10-16-2013, 07:59 PM
|
|
Replies: 34
Views: 1,115
I installed keel roller and moved boat up. My...
I installed keel roller and moved boat up. My question is how hard would it be to extend my tongue like 2'. Tires are load range C which can handle 1850 Each at 50 psi should be fine, my boat has new...
|
|
Forum: General
10-13-2013, 08:27 PM
|
|
Replies: 34
Views: 1,115
|
|
Forum: General
10-12-2013, 06:39 AM
|
|
Replies: 34
Views: 1,115
I recently swapped that trailer for a biggere...
I recently swapped that trailer for a biggere one. The dealer was very good about it, he gave me a much better trailer at no cost. I still had to do a little roller moving and sliding the bow roller...
|
|
Forum: General
10-01-2013, 09:06 PM
|
|
Replies: 2
Views: 150
Trailer roller spacing
Can anyone recommend a good roller arm spacing for the 75' 20 I just bought a venture single axle trailer and the spacing of the rollers port to starboard no matter how i slide the bracket doesn't...
|
|
Forum: General
08-20-2013, 08:18 AM
|
|
Replies: 34
Views: 1,115
I had read that the overhang should not be more...
I had read that the overhang should not be more than 10% of the length of the boat. It does not sway, but I have only driven local and have not gone more than 35-40 MPH. Since the pic's I lowered the...
|
|
Forum: General
08-20-2013, 06:07 AM
|
|
Replies: 34
Views: 1,115
Trailer questions
I recently purchased a used trailer and I had to move some rollers around because they were sitting under the strakes, I am not totally comfortable with the setup. I was told it had a 21' boat on it,...
|
|
Forum: Repairs
01-19-2013, 10:19 AM
|
|
Replies: 7
Views: 215
|
|
Forum: Repairs
01-19-2013, 10:19 AM
|
|
Replies: 7
Views: 215
|
|
Forum: Repairs
01-19-2013, 10:15 AM
|
|
Replies: 7
Views: 215
|
|
Forum: Repairs
01-19-2013, 08:07 AM
|
|
Replies: 7
Views: 215
Cost for stator
Wondering how much a stator would be for a 1994' 150 HP Evinrude Ocean Pro? Thanks:head:
|
|
Forum: Repairs
01-02-2013, 10:08 PM
|
|
Replies: 7
Views: 428
|
|
Forum: Repairs
12-27-2012, 03:39 PM
|
|
Replies: 7
Views: 428
yeah I was going to check the stator in the...
yeah I was going to check the stator in the spring, I need to get a puller from somewhere. As far as the lower, it could be, the end of the screw is always perfect, no shavings. What makes me wonder...
|
