|
|
#1
|
|||
|
|||
fuse panel
i bought a fuse panel from west marine its a 6 switch style fuse panel. i am kind of confussed on how to wire it there is 3 things + (positive) -(negitage) i got that but then in the middle there is one that says load (in thery would be the hot wire to what ever im wiring) with a male end put the + and - sides are all linked together with a screw in the middle. How do i run a negitive wire say from the bildge pump if there is no where to plug in to.
http://www.westmarine.com/webapp/wcs...classNum=50552 thats the link of the one i bought
__________________
I have a 1987 V20 Steplift with a 1987 johnson 140 2 stroke 
|
|
#2
03-18-2012, 11:28 PM
|
||||
|
||||
|
you need a ground buss bar..... fuse box/switch panel is for positive only negative stays always connected on the buss bar
|
|
#3
03-19-2012, 08:47 AM
|
||||
|
||||
|
Mine has a built in neg buss bar...but keep in mind fuses and switches break & connect the pos side...neg grounds somewhere else...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#4
03-19-2012, 09:36 AM
|
||||
|
||||
|
I looked at the picture of the terminals on your link. Looks like there are no 1/4inch terminals for the Neg wires. You'll have to solder them to the neg- terminal board or buy a bus bar (with screws or 1/4inch terminals). You might be able to find a 1/4inch terminal bus that will screw directly to the Neg- screw on your switch panel.
Question...does the panel you bought have fuses/breakers for each load or is it just a switch panel? If it is like the one pictured, it has no fuses and you will need a fuse block.
__________________
1984 V20 "Express" & 2003 Suzuki DF140 (SOLD!) 2000 GradyWhite 265 Express YouTube/SkunkBoat https://www.youtube.com/channel/UC4F...znGospVOD6EJuw Transom Rebuild https://www.youtube.com/watch?v=EEz94NbKCh0 https://www.youtube.com/watch?v=Oe_ZmPOUCNc
|
|
#5
03-19-2012, 11:52 AM
|
||||
|
||||
|
these are lighted switches, one plug is for power, 1 for ground, one is fro the light on switch, it should come with directions when you buy
__________________
1986 V20  Old Fishermen never die, we just SMELL that way!!
|
|
#6
03-19-2012, 01:41 PM
|
||||
|
||||
|
You will need a 60 amp fuse between the fuse panel and the battery. The switches are actually 15A breakers on the ones you gave link to from West Marine. (reset by turning off and then on again) They want to ensure that your positive lead wire from the battery to the panel is properly fused. The single screw design just makes it so you hook one ea positive and negative and then go to your load with the 1/4" spade connectors from there. Personally, I would stay away from it with the soldering iron. The soldered points on the negative board are for the led lights inside the breakers. On the positive board they appear to be the feed for the breaker switches and the led lights. Buy a terminal block for the negative wires. Label them in some way so if you have a problem it is easily diagnosed.
__________________
 1996 -19' NV Flats 115 Mercury 4-stroke 1983 -20' Wellcraft Center Console 250 XS
|
 |
|
|
Linear Mode
