|
|
#71
|
|||
|
|||
stringer question
on your old stringers were they straight to the outer shell mine were an a sixteenth to an eighth off the shell so far im stuck on what to do about the two boxes and getting them out
 looking good 
__________________
77 v20 cuddy cabin chevy straightsix 
|
|
#72
12-18-2011, 09:16 PM
|
||||
|
||||
|
Pic of bedded and glued stringers, And pic of cap getting prepped for lamination of 3/4 inch ply on top of existing 1/2 inch. I want to beef up the cap a little more.
Last edited by Kracker Jack; 12-18-2011 at 10:04 PM.
|
|
#73
12-19-2011, 10:39 AM
|
|||
|
|||
|
Keep up the good work
Kracker:
Can't see in your lastest pics, but I assume you have weep holes aft to allow and water to drain the the garboard plug? It also looks like your center stringer aft 90 is solid. You might want to notch the corner so water can drain from either side "JUST IN CASE" Keep up the good work! Kamikaze
__________________
 74 V20 CC with a 150 Johnson (Gone but not forgotten) 89 V20 Cutty with a Tower (Build in process)
|
|
#74
12-19-2011, 01:02 PM
|
||||
|
||||
|
Kamikaze I forgot to cut my 1/4 circles in my main at the transom. I glued them down and 20 minutes later I had a ahh **** moment!!!! I'm gonna end up cutting them with my rotoo zip tool on Thursday then glass a small strip of 1.5 csm on under edge to water proof. Thanks for looking out.
|
|
#75
12-19-2011, 07:07 PM
|
||||
|
||||
|
This question is for all you structual guys on here. I was thinking about returning my glass over my cap and tie it into the outside hull down the side about 2 or 3 inches. Is this a wise move? there is a reason why factory did not glass the insert or cap or guwals to the side of the boat. I personally think if I glass the cap in this manner to the side of the boat it will be a constant flex and crack issue ultimately leading to an astetic eye sore . Any opinions would be awesome. As you can see in the picture my cap is made of wood which Im gonna laminate a nother piece of 3/4 acx to to beef it up. Im then going to band the inside edge and outside edge with 3/8 acx router all edges and then glass with 2 layers of 1.5 csm. would this be a proper schedule for this application or should I go with one layer of 1708?
|
|
#76
12-19-2011, 08:29 PM
|
|||
|
|||
|
ok i see mine is made a lil diff i have no cap unless it rotted away and how do i get the fish boxes out without messing up my step into cuddy to lhe left is the step down and middle is the box and far right is the other box
__________________
77 v20 cuddy cabin chevy straightsix
|
|
#77
12-19-2011, 08:44 PM
|
||||
|
||||
|
im gonna move this over to your thread look there for my idea on box removal.
|
|
#78
12-19-2011, 10:11 PM
|
||||
|
||||
|
Quote:
|
|
#79
12-19-2011, 10:20 PM
|
|||
|
|||
|
no i have a big glass one that just gets screwed to the hull i have to replce the plywood in it to its rotten in the back and over the cuuddythis boat was just not well maintained and they just screwed whatever they wanted to where ever they wanted to and i went and joined the hull truth to get some more info
__________________
77 v20 cuddy cabin chevy straightsix
|
|
#80
12-20-2011, 02:53 AM
|
||||
|
||||
Lookin' good Kracker Jack! great thread, very informative Thanks!
__________________
1985 Wellcraft V-20, Evinrude ETEC 150: SOLD 1979 Marine Trader 44, twin Ford Lehman 120s 2006 Panga 14, Tohatsu 20
|
 |
|
|
Linear Mode
