|
|
#31
|
||||
|
||||
Re: trailer bearings / tires
Thanks Reel, well at least I slept good last night *:-/
I am not to worried about the spindle, because I assume I do not need to change it I dont have to, but If I do need to, well this thread is going to get much bigger ::) ::) The load 3500lbs, it is only a 1 axel trailer, and I assume I have been doing it all along with the same set up and I do not trailer it over 5 miles from my house so I should be all set ???
__________________
|
|
#32
04-26-2007, 11:01 AM
|
||||
|
||||
|
Re: trailer bearings / tires
Reel hits a good point!! But maybe the trailer was never rated for the boat, and you are getting the same thing??
Yes with this kit you change the spindle! You will have to look to see how yours come out? I am sure there will be some hammering involved and a few choice words But you can do it Nicky!
__________________
1986 V20  Old Fishermen never die, we just SMELL that way!!
|
|
#33
04-26-2007, 11:14 AM
|
||||
|
||||
|
Re: trailer bearings / tires
Thanks for the confidence :-/ ;D ;D
I am goingto redo the current ones today, tonight and if I can get them rolling, I may see if I can send the new ones back and upgrade them to a higher rated series. We will see. ::) Thanks again... I'll try to get some pictures up to ;D
__________________
|
|
#34
04-26-2007, 11:15 AM
|
||||
|
||||
|
Re: trailer bearings / tires
You're lucky w/ only 5 miles to ramp ... and I agree you'll be OK ...good luck w/ the swap-out...lots of good advice here, except nobody said to get a big bottle of GoJo ;D ...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#36
04-26-2007, 11:27 AM
|
||||
|
||||
|
Re: trailer bearings / tires
Go Jo...heavy-duty hand cleaner...great for cleanin' up yer hands after a round w/ old and new axle grease ;) ...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha
|
|
#38
04-26-2007, 11:38 AM
|
||||
|
||||
|
Re: trailer bearings / tires
Quote:
Don't we all, MJ...don't we all ;) ;D ;D ;D ...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha
|
|
#39
04-26-2007, 11:39 AM
|
||||
|
||||
|
Re: trailer bearings / tires
If you have a big vise or two saw horses to put the Hubs on, it will be good when banging out the races, they will just go out the bottom when banging them.
Make sure when putting the new ones in the cone goes up so the races have something to sit in! I hate when they are backwards!!
__________________
1986 V20 Old Fishermen never die, we just SMELL that way!!
|
|
#40
04-26-2007, 11:53 AM
|
||||
|
||||
|
Re: trailer bearings / tires
Quote:
Yeah, that'd be a BUMMA!! ;) ...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha
|
 |
|
|
Linear Mode
