|
|
#1
|
|||
|
|||
82 wellcraft v-20 cuddy
hello i just picked up an 82 v-20 cuddy and had a few questions about it. first off i need a motor for this boat and was wondering what size shaft would i need for this year? i have access to an 87 suzuki 200 hp for 800.00 bucks. even commpression, runs great around 300 hours, includs all controls sounds like a good deal. this motor is a 20 inch shaft.
also anyone put a bigger tank than a 60 gallon in there v-20? and would it fit? the boat was free by the way been sitting for a few years just needs good cleaning. 
|
|
#2
09-11-2006, 05:44 PM
|
|||
|
|||
|
82 wellcraft v-20 cuddy
hello i just picked up an 82 v-20 cuddy and had a few questions about it. first off i need a motor for this boat and was wondering what size shaft would i need for this year? i have access to an 87 suzuki 200 hp for 800.00 bucks. even commpression, runs great around 300 hours, includs all controls sounds like a good deal. this motor is a 20 inch shaft.
also anyone put a bigger tank than a 60 gallon in there v-20? and would it fit? the boat was free by the way been sitting for a few years just needs good cleaning.
|
|
#3
09-11-2006, 06:18 PM
|
||||
|
||||
|
Re: 82 wellcraft v-20 cuddy
Measure from the center of the transom down to the keel beneath the plug and you'll have either 20' or 25". Biggest tank factory for a V-20 was 60 gallons. I know of one that has 85 custom but that was after stringer and deck work. Welcome aboard.
Airslot
__________________
Airslot Airslot's V-20 Gallery
|
|
#4
09-11-2006, 06:18 PM
|
||||
|
||||
|
Re: 82 wellcraft v-20 cuddy
Measure from the center of the transom down to the keel beneath the plug and you'll have either 20' or 25". Biggest tank factory for a V-20 was 60 gallons. I know of one that has 85 custom but that was after stringer and deck work. Welcome aboard.
Airslot
__________________
Airslot Airslot's V-20 Gallery
|
|
#5
09-11-2006, 07:16 PM
|
|||
|
|||
|
Re: 82 wellcraft v-20 cuddy
also the cutout on the transom for the motor if it goes straight across its a 25" shaft if it goes across and in the middle has a additional drop its a 20" shaft. Z
__________________
1984 Step-Lift Cuddy&&1993 Johnson 200hp
|
|
#6
09-11-2006, 07:16 PM
|
|||
|
|||
|
Re: 82 wellcraft v-20 cuddy
also the cutout on the transom for the motor if it goes straight across its a 25" shaft if it goes across and in the middle has a additional drop its a 20" shaft. Z
__________________
1984 Step-Lift Cuddy&&1993 Johnson 200hp
|
|
#9
09-11-2006, 10:04 PM
|
||||
|
||||
|
Re: 82 wellcraft v-20 cuddy
From were the motor bracket sits on the boat to the bottom of the transom under the drain, is what shaft you need.
If it is a 25 don't give up on that motor!! They sell extension kits that will make it a 25. But they cost like $600 and can be done in about 2 hours!!
__________________
1986 V20  Old Fishermen never die, we just SMELL that way!!
|
|
#10
09-11-2006, 10:04 PM
|
||||
|
||||
|
Re: 82 wellcraft v-20 cuddy
From were the motor bracket sits on the boat to the bottom of the transom under the drain, is what shaft you need.
If it is a 25 don't give up on that motor!! They sell extension kits that will make it a 25. But they cost like $600 and can be done in about 2 hours!!
__________________
1986 V20 Old Fishermen never die, we just SMELL that way!!
|
 |
|
|
Linear Mode
