|
|
#1
|
||||
|
||||
How do I remove old wood grain dash 'stickers'?
Hey all, see pictures below. I have a 79 Cuddy that has very faded and worn stickers with wood grain look that just need to go on the dashes. Picture is port side only, but have similar across the gauge area that I want to remove.
As you can see, I started with a paint scraper, but clearly I need something more to get down to the gelcoat. Any suggestions on how to get these off? They are very sun baked and hard, but still pretty well on there. I have some paint stripper, intended for stripping wood furniture, but not sure if that may damage the gelcoat. My goal is to just have the gelcoat exposed as the dash area. By the way, note the fully installed windshield, what a hack that was before, held in with 5200 only...   This is before, with windshield removed: 
|
|
#2
05-01-2010, 04:05 PM
|
||||
|
||||
I've had a lot of success removing contact stickers with a hairdryer. The heat softens the glue bond and normally you can just peal the sticker off. Work from one corner and peal with your hand while holding the dryer just in front of where you're pealing. I've used that trick to remove numbers off a hull, names of boats and lots of other things. You might want to try it. If you're going to use a heat gun instead of a hair dryer use caution.. you don't want to damage the fiberglass under the sticker with too much heat in one spot.
A 1200W hair dryer is what I use.... seems to have just enough heat to do the job.
__________________
1987 V20 w/1987 150HP Yamaha on a Shoreland'r Trailer 1978 16.5 Airslot w/1996 120HP Force on a Four Winns trailer 1996 V21 w/1993 200HP Mercury on a Shoreline Trailer All towed by a 5.7L Hemi Durango. If God didn't have a purpose for us we wouldn't be here, so Live simply, Love generously, Care deeply, Speak kindly. (Leave the rest to God)  Silence, in the face of evil, is itself evil. Not to speak is to speak, not to act is to act. God will not hold us guiltless.
|
|
#3
05-04-2010, 08:14 PM
|
||||
|
||||
|
Yeah, heat is the best. Strong hair dryer, or heat gun would be better. Then you can take a spray can of brake cleaner to remove the rest of the residue.
__________________
Captain Jon
|
|
#4
05-06-2010, 05:59 AM
|
||||
|
||||
|
Leave it there...cut a piece of 1/4" Starboard to fit the area...it'll also kill out (cover) the screw holes and the hole under the clamshell...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#5
05-06-2010, 07:56 AM
|
||||
|
||||
|
Quote:
__________________
Heavily medicated for your protection.
|
|
#6
05-06-2010, 01:50 PM
|
||||
|
||||
|
I was thinking that. I need to re-do my dash as well, so I'll pick up a large enough sheet of stareboard to do that. I've seen it at West Marine, any suggestions on other potential (less $) options? WM tends to price pretty high, but I don't know who else carries that stuff
|
|
#7
05-06-2010, 02:14 PM
|
||||
|
||||
|
you could try looking up a local industrial type plastic supplier. not sure if they will deal in less than full sheets but it might be worth a try. I've had to buy a few sheets here and there for some customers and the one I use around us here sells them cheaper than retail.
__________________
1986 V-20 1986 Yamaha 150 HP
|
 |
|
|
Linear Mode
