|
|
|
|
#1
|
||||
|
||||
Good find on that enclosure...it'll STRETCH the season for ya...nice lookin' V...you and yer little companion have lots of stories to to come...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#2
03-21-2009, 09:17 PM
|
||||
|
||||
|
Very nice Wilson, let me know when you want to hook up on the valley since we can't do it on Hopatcong like we talked about. They are slamming Lakers there now with some nice Rainbows and Browns coming in
__________________
Willy 1986 V20 Old School 1992 V20 1992 150 Yamaha 1997 HydraSport 2250 Vector 2009 17' G3 Outfitter "G Spot" http://www.youtube.com/watch?v=TDebw...eature=related "I won't be wronged, I won't be insulted and I won't be laid on a hand on. I don't do these things to others and I require the same from them" JW
|
|
#3
03-22-2009, 10:17 PM
|
||||
|
||||
|
Quote:
In the meantime if you need someone to help you wet a line let me know....
__________________
1986 V-20 1986 Yamaha 150 HP
|
|
#4
03-26-2009, 08:03 AM
|
||||
|
||||
|
do the through the hull come with scuppers on the inside to stop the water from coming in on the deck??i looked on the site and could not find them..
__________________
1986 v20 steplift with 115 yamaha...Never forget the friends and heros of 9/11....Support Juvenile Diabetes Research Foundation (For my son, Diagnosed 6/2/2007).......
|
|
#5
03-26-2009, 10:55 AM
|
||||
|
||||
|
Quote:
I bought the PVC check valves from Mcmaster Carr, they are for plumbing applications and not made specially for boats. They were a little over $10 a piece. PVC Swing Check Valves 
Pipe End-to- Cv Clear PVC White PVC Size End Lg. Factor Each Each 1" 4 9/16" 656274T74 $17.17 45275K34 $10.84 I wouldnt rush out to get them just yet because I am not sure if they are going to work . I cut the barb off the through hull and screwed them right to the through hull. Problem is because of the length of them and the fact that the through hull is mounted on a slight angle the inlet to the check valve is now at about the same height as the floor drain. As a result it is trapping water in the drain and it is not draining too quickly. I am going to relocate them in the middle of the hose section and see if I can get the height right. I'll let you know how it works out.
__________________
1986 V-20 1986 Yamaha 150 HP Last edited by RWilson2526; 03-26-2009 at 03:02 PM.
|
|
#6
03-21-2009, 09:50 PM
|
||||
|
||||
|
If i may ask, where did u pick up the through the hull fittings etc??i have to change mine out also, and cant find them and was it a difficult job??thanks
mark
__________________
1986 v20 steplift with 115 yamaha...Never forget the friends and heros of 9/11....Support Juvenile Diabetes Research Foundation (For my son, Diagnosed 6/2/2007).......
|
|
#7
03-22-2009, 10:11 PM
|
||||
|
||||
|
Quote:
dont worry about the "sale ends today" We established its free shipping whenever you purchase. changing them was a piece of cake at least on mine....the inside nut came off very easily and a few wacks with a hammer knocked the old ones right out. a little scraping inside the hole to clean it up and a light wet sand on the outside and the new ones were good to go in. The ss ones have two tabs in them that you will need a radiator spud wrench (see picture) so you can stop it from spinning when you tighten the inner nut. they probably have other tools for that but I happen to have one because I have cast iron radiators in my house which I changed the nipples on. you dont need to get them crazy tight anyway i dont think. the sealant is what holds them in place I think 
__________________
1986 V-20 1986 Yamaha 150 HP
|
 |
|
|
Hybrid Mode
