Heat wave pics

fillet1 · #1 01-30-2005, 08:11 PM

Since it has finally warmed up here to above freezing, I got under the cover to fiddle around a bit!!

1st pic: Shows the starboard frame I made for the helm.

2nd pic: Shows new rod boxes From FPMARINE that I finished out and installed yesterday.

3rd pic - i took off the rear bulkhead door to either replace or refinish. I'll probably install a hatch there.

4th pic- a few holes to fill - hell it looks like swiss cheese!

last one - I'll be replacing this lounge with a new one or a pedestal seat

Mac_Attack · #2 01-30-2005, 10:49 PM

Nice job of photo taking with the boat under wraps! Your cabin doors look new and is that a tackle locker on the port side of the bulkhead? Bill Mc ;D

fillet1 · #3 01-30-2005, 10:56 PM

MAC

The doors are original, just took em off and sanded/oiled them.

That is a tackle locker on the port bulkhead. Its a Tempress and I need a new door for it. I cant seem to find one yet.

bigshrimpin · #4 01-31-2005, 03:13 AM

Fillet - your boat looks great. I like the full transom with the in floor baitwell.

If you need a new temptress hatch there are a few on ebay. Not sure what size you need.

http://cgi.ebay.com/ebaymotors/ws/eB...category=26451

http://cgi.ebay.com/ebaymotors/ws/eB...category=26451

reelapeelin · #5 01-31-2005, 09:53 AM

Fillet...hey man your dash looks GREAT 8)....that FULL transom is the deal...

Suggestion...if box under lounge is sturdy, remove seats, add lid(coverd w/vinyl), put swivel seat forward...keep that storage space in the box....just an idea :)...

fillet1 · #6 01-31-2005, 10:59 AM

Bigshrimpin - thanks for the links - the first one is what I need, but I have to double check the size.

RAP - that is a good idea. But for today at least, ;) I am thinking that i just want another pedestal and seat. I like the clean interior look of Seabird's 85 in the gallery. The only lounge that I can find that has a 16 inch base is over $300.00.

Anyone know where I can get a seat that matches my helm seat?

I am also looking for the threaded knobs for the ends of the seat swivel/slider. I just took the whole assy apart and rebuilt it.

reelapeelin · #7 01-31-2005, 12:54 PM

Yeah, I'm w/you on the clean look of 2 pedistals...if I hadn't needed fuel capacity, I'd have gone the same route...

Your helm seat doesn't show much in photos above(I'll look in the gallery), looks like Todd seat from a few years back....just looked in Boaters World, West and Bass Pro master cats and didn't see 'em, but I'll keep an eye out...

Your boat's comin' along great 8)....

fillet1 · #8 01-31-2005, 02:20 PM

I couldnt find any Manufacturer's marks on it other than an "M" serial #? If you look in my "new member" there is a pic that may show the seat, but not with much detail.

I want the seats to match if I go the pedestal route. If I cant find a match then I am looking at buying two new seats, one that needs a pedestal and spider, the other to fit the existing one. That scenario becomes a $400.00 deal which is more than the right size lounge.

I did see that Fpmarine has a bunch of seats etc cheeep! I may call down there and see what they have in a matching set.

Maybe next year I'll trade in my 115 and get me one of those nice shiny Hondas!!! ;D

reelapeelin · #9 01-31-2005, 02:43 PM

Maybe by then I'll have figgered out which prop you should use ;)....

CT_V-20 · #10 01-31-2005, 03:19 PM

Your boat looks great. The rod boxes look AWESOME! Do you still have the stern seat? I noticed the hardware for it in the deck. I have mine, it is sitting in my shed. I'm mixed on it, I left it out all of last season and really liked all that cockpit room. And if you need extra seating, there is PLENTY of room for a couple folding deck chairs.