|
|
|
|
#2
08-11-2013, 01:34 PM
|
||||
|
||||
Quote:
Wolf yer hard work has paid off...she sure looks great!!...can't wait to see new graphics!!... Greene's right about the trim tabs, but they'll come in time...enjoy til then!! Yer REELY gonna enjoy that full enclosure when the thermometer starts droppin' this Fall...I call those SEASON EXTENDERS cuz that's what they do...amazing how well those tops hold heat from a small propane heater...Boat $$ well spent there!!... Great PICTURES!!...keep 'em comin'!!... 
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#3
08-11-2013, 01:48 PM
|
||||
|
||||
Great thread and pics! All worthwhile repairs and mods. Good job!
__________________
1985 Wellcraft V-20, Evinrude ETEC 150: SOLD 1979 Marine Trader 44, twin Ford Lehman 120s 2006 Panga 14, Tohatsu 20
|
|
#5
08-15-2013, 09:25 PM
|
||||
|
||||
|
Lot's more done shake down tomorow afternoon
Well I got the rest of my (PRE-SHAKE DOWN LIST) acomplished today, and I am taking the (NAUTI BUOY) out tomorow to CONGAMOND lake for some trial runs , will post photos of that tomorow night, but here is what has been done since last post.
1) replaced the old fuel filler cap and vent (both were SHOT and the hull needed glass repair were they were.) Also since the prievious owner had replaced the fuel tank but not the lines a month before I bought her I changed them also.     2)I was tired of rain leaking into the cabin thru the anchor line cap so I went to HOME BOY DEPOT got some 6" pvc pipe with ennd flanges , some pvc contact cement and WALA now the water runs straight into the anchor rode locker and out to the bilge. I also thought that the rode locker needed some work so I re did it also ( resin and new piaint )   3) I had redone the teak wood a while back on the bow slide hatch cover but I decided to and more lacquer and put some tefalon film under the hatch to make it slide better and seal it .  4) AND NOW THE DECALS AND GRAFIX ARE ON !! I have a great sighn shop very close to my home , and they are GREAT Linda has been doing my rebuild boats for years now and she never stops to amaze me with what she can do from my simple ideas, let me know what you all think about the name and custom decals. I also was lucky when I went to register her I was able to get a set of #'s the work on the boat MS 2084 VE since its an 84 20' v I think it works      5) also to any one having problems using 3M 5200 Try using this I can clean up my hands and tools ect. Its the only thing I have found that works 
Last edited by GREYWOLF; 08-16-2013 at 04:04 PM. Reason: photo
|
|
#6
08-16-2013, 09:06 PM
|
||||
|
||||
 ...Wolf you sure got all the right stuff DONE on yer V!!..GREAT JOB...the name is KILLER!!...and yer right about the graphics shop...she apparently very talented and knows what she's doin'...Can't wait to see the splash pics from tomorrow...get a shot or two up on plane iffn ya can!!...  Lookin' good, Man..lookin' good... 
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha
|
|
#8
09-07-2013, 09:14 AM
|
|||
|
|||
|
very nice
|
|
#9
09-10-2013, 10:50 AM
|
||||
|
||||
|
Wolf I REELY LIKE all the work you've done!!...that floor looks great for a lot of reasons, one being no screw heads showing and very little visible transition fron lid to deck!!...That makes the floor look about twice as big!!...Nice Job!!...
And the new rope in the rub rail, too..nice upgrade!!... That's a TWO BEER post there!!... 
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
