|
|
|
|
#1
|
||||
|
||||
With new piston pin bearings and washers.
__________________
1984 V-20 Center Console 1985 90 hp Merc. American by birth, Southern by the grace of GOD. Never let your hobby become a job but rather let you job become your hobby. http://www.wellcraftv20.com/gallery/turbine_doc_84_cc 
|
|
#2
03-18-2010, 04:58 AM
|
||||
|
||||
|
Putting all 6 pistons in at the same time was pretty easy with the ring compressor kits.
__________________
1984 V-20 Center Console 1985 90 hp Merc. American by birth, Southern by the grace of GOD. Never let your hobby become a job but rather let you job become your hobby. http://www.wellcraftv20.com/gallery/turbine_doc_84_cc
|
|
#3
03-18-2010, 04:59 AM
|
||||
|
||||
|
Installing the upper and lower bearing end caps.
 
__________________
1984 V-20 Center Console 1985 90 hp Merc. American by birth, Southern by the grace of GOD. Never let your hobby become a job but rather let you job become your hobby. http://www.wellcraftv20.com/gallery/turbine_doc_84_cc
|
|
#4
03-18-2010, 05:00 AM
|
||||
|
||||
|
Inspecting the rings. All OK, none broke on the way in.
__________________
1984 V-20 Center Console 1985 90 hp Merc. American by birth, Southern by the grace of GOD. Never let your hobby become a job but rather let you job become your hobby. http://www.wellcraftv20.com/gallery/turbine_doc_84_cc
|
|
#5
03-18-2010, 05:04 AM
|
||||
|
||||
|
Some where along the way I forgot to take pictures but here it is back on the mid section and wired up.
__________________
1984 V-20 Center Console 1985 90 hp Merc. American by birth, Southern by the grace of GOD. Never let your hobby become a job but rather let you job become your hobby. http://www.wellcraftv20.com/gallery/turbine_doc_84_cc
|
|
#6
03-18-2010, 05:05 AM
|
||||
|
||||
|
Thats all the pictures I got for now.
__________________
1984 V-20 Center Console 1985 90 hp Merc. American by birth, Southern by the grace of GOD. Never let your hobby become a job but rather let you job become your hobby. http://www.wellcraftv20.com/gallery/turbine_doc_84_cc
|
|
#7
03-18-2010, 06:51 AM
|
||||
|
||||
|
Can you imagine trying to do the rings without the tool?
 Those motors scream...Do you have it running?
|
|
#8
03-18-2010, 10:33 AM
|
|||
|
|||
|
Turbine - I am worried about the journal in this picture. Were those water marks or just oil? . . . Did they come out with crocus cloth? In this pic . . . They look like a bit like chatter marks.
|
|
#9
03-18-2010, 03:32 PM
|
||||
|
||||
|
Big Shrimpin I believe that is the reflection of the metal building/Quonset hut.
|
|
#10
03-18-2010, 10:21 PM
|
||||
|
||||
|
Yes those marks are a reflection. You had me worried for a minute but if you look close you will see a redish line down the middle, that is the reflection from my engine hoist.
I have more invested in the tools than I would like to confess to but I wanted to make sure it went together right. Yes she is running, I have a short video of her first time. I did not have an hour meter before so I installed one before I fired it up for the first time. I now have 1.3 hours on it but they are all on the muffs or in a tub. I need to put it in the water to set the idle while in forward gear. I have rebuilt auto engines before but never a outboard let alone a 2 stroke. All and all I am happy with the way it has turned out so far. I'll try to keep you posted as the break in process. Durwood
__________________
1984 V-20 Center Console 1985 90 hp Merc. American by birth, Southern by the grace of GOD. Never let your hobby become a job but rather let you job become your hobby. http://www.wellcraftv20.com/gallery/turbine_doc_84_cc
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
