|
|
#11
|
|||
|
|||
what kind of wood did you use and how thick? how are you going to mount itand are you going to put in a roller?
__________________
love to fish 
|
|
#12
09-28-2009, 12:30 PM
|
|||
|
|||
|
Not to bash you but i think i would have used a heavier cloth or at least a few more layers of what you used. It looks like you used 6oz finish cloth. Only reason i say is because that thing is going to take a beating up front on the boat and it being subject to anchor chain and abuse it wont take much at all to get to the wood. Nice gel coat job tho. i suck something terrible with gel coat - pretty handy with epoxy tho.
|
|
#13
09-28-2009, 01:10 PM
|
|||
|
|||
|
Quote:
|
|
#14
10-18-2009, 08:50 PM
|
|||
|
|||
|
Here we go finish at last, Its cold and I quit at 6 PM its freezing :) 60 degrees ! Don't laugh ! Can't believe I am saying this..
I modify the Bow rail to follow the anchor platform like I have seen it on boats with this kind of setup. Angle grinder with a cutting wheel used to cut the pipes it cuts like butter ! As for the 90 degree elbow in the middle of the rail, I will build a mount for a 360 remote flood light or spotlight whatever its called, sometime in the future when the price is right :) The wires will be fish through the rail into the cuddy for a clean look. I use the Bow rail I purchase a while back from a member on this site about two years ago.. Notice all the screws are mounted completly through the platform and the deck with aluminum plates inside for extra strength. I will never have a chain or rope attach full time, to protect my gel coat, using a clip I will connect the rope prior to launching (stay tune one of my co-captains will launch it without any rope attach I just know it ) Opps I just notice I did not remove the plastic tie strap I use to secure the anchor during the installation. As for the 12" cleat it will be handy when trying to lace a 1/2 " rope ? Paid $60 at West on ebay its 2 for 35 but hey I was in the get it done mode ! And YES I hate working with 5200 ! Only acetone cleans it ! Hey my lights am I good ? Not sure now looking at it .. Seat completion next ! Bow Rail before the modification Picture from a year ago ..Observe the teak before and after..     Please excuse the dust , I did now clean up after my work my bad, Yes 5200 still showing two left screws !  
Last edited by nymack66; 10-18-2009 at 09:55 PM.
|
|
#15
10-19-2009, 06:42 PM
|
||||
|
||||
|
looks great ny, i might have missed it, but why not install a deck pipe and run the chain & rode down to the anchor locker in the bow. i used to do a lot of diving and i don't feel comfortable without at least 25 or 30 feet of chain.
neat install, i like the backing plates...
|
|
#16
10-19-2009, 07:01 PM
|
|||
|
|||
|
Looks great! I like the look of that size. Can you tell me the dimensions length and width? That is my next project on mine when I bring it home next month. I am also thinking about the kind of pulpit where the anchor goes through ( don't know what it is called) so I can use my existing bow light.
|
|
#17
10-20-2009, 07:33 AM
|
||||
|
||||
|
Nice work, NY!!...gonna make hookin' that baby LOTS easier...great work and thanks for the pics!!...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#18
10-20-2009, 06:24 PM
|
||||
|
||||
|
great job , and that bow rail came out awsome.
__________________
1987 Dual Console / 2007 200 hp E-Tec 
|
|
#19
10-20-2009, 06:58 PM
|
|||
|
|||
|
Quote:
Thanks all for the kind words guys
|
|
#20
10-20-2009, 07:07 PM
|
||||
|
||||
|
Looks great, I've been meaning to do one for a couple of years now.
__________________
1985 Wellcraft V-20, Evinrude ETEC 150: SOLD 1979 Marine Trader 44, twin Ford Lehman 120s 2006 Panga 14, Tohatsu 20
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
