Motor ID help?

[babydrilll]

I think the cap fell out of the hole above the V$.

Carl

[THEFERMANATOR]

That is an 85-87 style 140. It came origanally with a small bore, but you have to pull the heads off to see if it has been replaced with a late model. The ignition systems and such are pretty universal from 85-87 with the exception of 85 having a 6100 RPM limiter and 86-87 had a 6700 RPM limiter.

[babydrilll]

Thanks you for all your help.

Carl

[nymack66]

I notice 328624 stamped on the engine head, mine has the same number and mine is 1987 140 V4 small bore looper, however the heads are inter changeable...
To be sure if its a 87 , post the part number on the power pack I know for sure ..If its a 87 there is only 2 model for the 140's J140TLCUA 1987 and J140TXCUA 1987 your clearly shows a Tilt & trim so if its a 87 then its model J140TLCUA
If you have a CDI pack install the number should be CDI 113-3101

[Skools Out]

the power pack won't help either due to you can put 85 to 87 wiring on V4 loopers up to about 94, and no that's not a TL model due to it's a 25 inch motor so is a J140TX**.

[nymack66]

I stand corrected . If you cross reference the pack on CDI charts the 87 is unique ..
Here is how I found out what mine is, remember I went through the same thing and you guys help me big time ...
I ref the pack numbers, screws on the butterfly 3 = 140 hp, numbers on the power head, numbers off the coils, numbers off the carbs, jets sizes and called it a 87 since :)
It only took me 4 months plus !

[THEFERMANATOR]

85 is the odd ball, 86 and 87 both work the same in the packs. 85 is also the oddball in more ways than one. 85 had a unique intake different from all other 140's as well as a special tuner that didn't run for crap down low as it was HUGE. Remember that 85 was the first year of the 90 degree loopers, and the 120/140 were the first to hit the streets. The 200/225 V-6's weren't official until 86 once OMC had ironed out most of the looper bugs. The other problem is that so many parts are interchangeable on the loopers with only small changes and iding an engine that is over 20 years old after god knows how many others have wrenched on it is just about impossible unless you tear it down and go through every nut and bolt in it.

[RWilson2526]

Jesus, how do you guys know this stuff? impressive to say the least.

[Skools Out]

well i've worked on them seems like forever OMC wise, and currently own 4 of the Johnson / Evinrude 140's one set is a counter set. plus have a complete set of J/E factory shop manuals for yrs 1980 to 2005 all hp's including the 4 stroke stuff by Suzuki. a lot of the guys here say i have the fastest fence in the south. it only has 730 hp on it lol.

pics of fence lol







pics of frankinmotor

[THEFERMANATOR]

Originally Posted by RWilson2526

Jesus, how do you guys know this stuff? impressive to say the least.

The exhaust ports below the cowling are the dead giveaway to it being an early model looper. In 88 they all went to the higher exhaust port. Also the single pack off on the side vs the big one in the middle also indicates 85-87. A stock 85 140 would have had a V6 style lower with the bigger prop, but in 86 most had the V-4 lower and 87 many went back to the V6 lower on 25" shaft engines. Just a few of the identifiers to narrow em down.