|
|
|
|
#1
|
||||
|
||||
Quote:
Ray, I'm pretty happy w/the overall performance of my Honda 150...have had it since '04...a little heavier than my '74 likes (which is why I'm anxious to try out trim tabs I've just added) and it isn't as strong outta the hole as the gas-suckin' rude 150 2-stroker that used to be on it... What I DO like about it is it starts and runs flawlessly EVERYTIME and although I didn't have numbers (GPH, etc) I can tell ya I'm using CONSIDERABLY less gas than before...tops out at 42 MPH and cruises at 30-32 MPH...used to be I didn't leave the dock w/out toppin' off...now I'll run 3-4 trips before gassin' up... Franco has a 150 Yam 4-stroke on his 20' CC and is happy w/his...hopefully he'll chime in here...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#2
04-04-2009, 07:47 AM
|
||||
|
||||
|
I had to put off repowering this year since I built a shop and have plans for replacing my floor and repairing/replacing my stringers. I am definitely going with the f-150 and I am figuring an average of 4 mpg.
__________________
1975 V-20 w/1996 225 Johnson
|
|
#3
04-24-2009, 11:56 AM
|
|||
|
|||
|
You can use these to get a good idea of what it will do, just find a test with a boat of similar size and hull design as you V and you will be pretty close.
http://www.yamaha-motor.com/outboard.../perfbull.aspx
__________________
*************************************** Stay Safe!  Sold - 1984 V-20 Cuddy with a 2003 Johnson 140 hp gas sippin 4-stroke. 1995 Ranger 250C with a 2015 Suzuki 300 hp 4-stroke.
|
|
#4
04-24-2009, 12:09 PM
|
|||
|
|||
|
i wouldnt expect an awesome holeshot.
|
|
#5
04-24-2009, 04:16 PM
|
||||
|
||||
|
If I had it to do over...it'd be an E Tech...which was not available in this HP range when I needed a motor...even more so now they've been out for a few years and proven themselves...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha
|
|
#6
04-24-2009, 04:51 PM
|
|||
|
|||
|
Quote:
|
|
#7
04-24-2009, 07:17 PM
|
||||
|
||||
|
In 07 we repowered with an Etec 150. Couldn't be more pleased. The top end we acheived was 46MPH at 5100 Rs with a stainless prop. Lumber has a 200HP Etec which is the same as the 150 with some computer adjustments. Just as cterrebonne says make sure your dealer knows what he's doing with the Etec. Billy Mac
__________________
 Now being pushed with the Force of an E-Tec! http://www.wellcraftv20.com/gallery/...1990-V20-Sport http://www.youtube.com/watch?v=9ESnJm4uxug
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
