|
|
#21
|
||||
|
||||
Quote:
|
|
#22
03-17-2021, 12:39 AM
|
||||
|
||||
|
grinding away
Started playing with the liner, little modification to marry up to the transom
Stringers had 1/8 to 1/2 inch gaps filled with goop before we pulled the liner. Workmanship in the hull looks like it was started on a Monday and finished Friday afternoon. liner was a different team ! Set our forms on the stringers with the liner in, put in temporary now till the next batch of seacast arrives encasing the rod compartments in glass too IMG_5599.jpg IMG_5709.jpg IMG_5708.jpg IMG_5686.jpg
|
|
#23
03-17-2021, 12:44 AM
|
||||
|
||||
|
|
|
#25
04-03-2021, 10:27 AM
|
||||
|
||||
|
update
A lot going on and not much time to post
Got the stringers done to height after putting the liner in for measurements, back off last night and hull moved into glass bays for capping off the stringers today Have decided to rework the liner too since were in this deep, pulling all hardware off it, new bulkheads and more. Restoring original teak. IMG_5967.jpg IMG_5975.jpg IMG_5719.jpg IMG_5760.jpg IMG_5821.jpg
|
|
#26
04-03-2021, 10:41 AM
|
||||
|
||||
|
date part two
Did a test area of bringing back the original gelcoat. first pass on the gelcoat with 400 in the picture, will most likely go to 800, then 1200 and then to 1500 (or more) if needed. The 400 seems to bring the color back about 80%.
Nice thing is they were not bashful with the gelcoat back in 81, pretty thick IMG_6019.jpg IMG_6020.jpg IMG_6037.jpg IMG_6089.jpg IMG_6092.jpg Last edited by Dana A; 04-03-2021 at 02:59 PM.
|
|
#27
04-04-2021, 10:51 AM
|
||||
|
||||
|
A few more from yesterdays progress. I just love the quality of the 80's teak
IMG_6102.jpg IMG_6107.jpg IMG_6111.jpg IMG_6110.jpg IMG_6108.jpg
|
|
#28
04-13-2021, 10:47 PM
|
||||
|
||||
|
Had her in for a fitting and sizing Sunday
Working the oxidation off on the hull and think paint job on the liner might be in order IMG_6366.jpg IMG_6375.jpg IMG_6288.jpg IMG_6294.jpg IMG_6296.jpg
|
|
#29
04-13-2021, 11:08 PM
|
|||
|
|||
|
Looks great!
__________________
billfish16 V20 Cuddy 1982 2002 Mercury 200hp
|
|
#30
04-13-2021, 11:27 PM
|
||||
|
||||
|
Boys are cranking away on her I'm doing the initial sanding above the waterline till I get down to 800 then Ill let them at it. below waterline for now for them.
Had to pull them off the wellcraft to do the bottom and buff the hull on the big boat to get it in, They banged it out in an afternoon. 12:30 am think ill head home now lol getting to be a habit IMG_6278.jpg IMG_6280 (2).jpg Some of our videos for your entertainment https://www.youtube.com/channel/UC9g...lO55p54ALvpASA Last edited by Dana A; 04-14-2021 at 12:18 PM.
|
 |
|
|
One of the best V for 2021 for sure when you are done with this baby. I have to do my stringers one day, they a-ok for now
Linear Mode
