|
|
#11
|
||||
|
||||
those things are sweeeeeet. I might have to put a pair of them on my boat too. Nice work!
|
|
#12
09-27-2009, 11:46 AM
|
||||
|
||||
|
Hey Wilson
Do they interfere with the rod holders? Where did you get them? thanks
__________________
Tis better to be quiet and thought a fool than open your mouth and prove it!! 1991 V-20 cuddy I/O 350 volvo duo prop, 1998 15ft Grumman 9.9 Johnson  
|
|
#13
09-27-2009, 12:23 PM
|
||||
|
||||
|
__________________
 '75 Cuddy with '00 Johnson Ocean Pro 150 horse Benny
|
|
#14
09-27-2009, 12:29 PM
|
||||
|
||||
|
Quote:
here's a link to where I posted them a few weeks ago.... man the rod holder almost got me....I checked and rechecked to make sure I was no where near steering cables/wires but forgot about the rod holders.. I cut the first hole and the rod holder was encroaching into the space by like 1/2" or less cutting across the top left hand corner. fortunately I cut the 4 corners of the fiberbglass out with a hole saw and I was able to push the hole saw in further and take a perfect crescent shaped piece out of the plastic tube of the rod holder, rods still fit in no problem. (if they were ss I would have been screwed. If I had only moved them back another 1/2" or so I would have had no problem...(turns out on the port side I did not have that problem as the rod holders are not installed identical on both sides (close but not exactly) Willy, I kind of half assed it, right now they are only screwed into the 1/4" or so fiberglass....my intention was to through bolt as I am pretty sure I can reach them from the aft hatches but I didnt have all the hardware and I had a nice supply of #10 screws. I had some free time yesterday (rare) so I just used sealant and screws. if they loosen up on me on I'll through bolt them with some nice fender washers or reinforce with some wood behind the hole.
__________________
1986 V-20 1986 Yamaha 150 HP
|
|
#16
09-27-2009, 07:39 PM
|
||||
|
||||
|
Winner, winner, chicken dinner!!...2 pages and still climbin' on subject of cupholders...since 2003 I don't recall ever this in-depth discussion about cupholders...but no doubt these are the "specialest" featured yet
Wall is 1/4" thick and you used #10 screws and sealant, they ain't goin' nowhere... 
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#18
09-29-2009, 08:35 PM
|
|||
|
|||
|
Now, I just need a cupholder for my TransAm. Seems they thought nobody would want to drink while driving it! Not the first cupholder anywhere in it anywhere. Dangdest thing!
|
|
#19
09-29-2009, 08:40 PM
|
||||
|
||||
|
Quote:
__________________
1987 Dual Console / 2007 200 hp E-Tec 
|
|
#20
09-30-2009, 07:50 AM
|
||||
|
||||
|
i remember when the japanese car companies got in the mini van business in the 80's. they could not understand why a 7 passenger vehicle needed 12 cup holders. they are like electrical outlets, can you ever have too many.....
|
 |
|
|
Linear Mode
