|
|
|
|
#1
|
||||
|
||||
Extend your transom height
Here's a great example on extending your transom to keep water out. It's a Mako but will give you an idea. He installed a 30" motor on a jack plate. A cheaper alternative than going to a full blown closed transom.
http://classicmako.com/forum/topic.asp?TOPIC_ID=7883
__________________
http://img.photobucket.com/albums/v2...tz/captain.gifhttp://img.photobucket.com/albums/v2.../2sharkfin.gif&&&&SOMEWHERE IN TEXAS A VILLAGE IS MISSING THEIR IDIOT! 
|
|
#2
02-14-2006, 12:13 PM
|
||||
|
||||
|
Re: Extend your transom height
Looks like a great job!! And I bet it works good!!
But he says he used 1/8" alum. There must be a mistake there cause that would not hold up for nothing!! Way to thin!! I bet he ment 1/4??
__________________
1986 V20  Old Fishermen never die, we just SMELL that way!!
|
|
#3
02-14-2006, 12:18 PM
|
||||
|
||||
|
Re: Extend your transom height
Unless its that tempered aluminum, that stuff is tougher than steel. If it was cast 1/8th no good. I got a sample piece of that stuff thay makes those boats out of up by you MJ, 1/8th and holy sh!t strong
__________________
Willy 1986 V20 Old School 1992 V20 1992 150 Yamaha 1997 HydraSport 2250 Vector 2009 17' G3 Outfitter "G Spot" http://www.youtube.com/watch?v=TDebw...eature=related "I won't be wronged, I won't be insulted and I won't be laid on a hand on. I don't do these things to others and I require the same from them" JW
|
|
#4
02-14-2006, 12:35 PM
|
||||
|
||||
|
Re: Extend your transom height
Well, we can forget using aluminum channel stock on a V-20 due to the curved transom >:( Not that I plan on having to use it. :)
__________________
 1994 Wellcraft V21
|
|
#5
02-14-2006, 12:44 PM
|
||||
|
||||
|
Re: Extend your transom height
I have never seen that alum?? I will have to look into it!!
As for using channel you could if you cut it and bend it then have someone weld the cuts were you bent it
__________________
1986 V20 Old Fishermen never die, we just SMELL that way!!
|
|
#6
02-14-2006, 06:29 PM
|
||||
|
||||
|
Re: Extend your transom height
Quote:
Willy, are you talking about the sample from "Black Lab Boats"? If so, that sample is 1/4", what they use on their hulls, they use 3/16" for the sides.
__________________
http://img.photobucket.com/albums/v2...tz/captain.gifhttp://img.photobucket.com/albums/v2.../2sharkfin.gif&&&&SOMEWHERE IN TEXAS A VILLAGE IS MISSING THEIR IDIOT!
|
|
#7
02-14-2006, 08:20 PM
|
||||
|
||||
|
Re: Extend your transom height
Yea thats the company Tin but the piece they sent me was not 1/4
__________________
Willy 1986 V20 Old School 1992 V20 1992 150 Yamaha 1997 HydraSport 2250 Vector 2009 17' G3 Outfitter "G Spot" http://www.youtube.com/watch?v=TDebw...eature=related "I won't be wronged, I won't be insulted and I won't be laid on a hand on. I don't do these things to others and I require the same from them" JW
|
|
#9
02-15-2006, 09:18 AM
|
||||
|
||||
|
Re: Extend your transom height
Great idea and well executed...one step further would face the inside of the extension w/aluminum...or 1/4'' Starboard...heck, for that matter, the whole job, inside and out, I'd rather do w/plastic...never worry about the paint comin' off or gettin' bent or dented...JMHO... ;) ;D...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#10
02-15-2006, 10:46 AM
|
|||
|
|||
|
Re: Extend your transom height
The pic with the 2 boats side by side, look how far out of the water the motor is on the mako. Ya think its tilted up or is that all way down. The GW motor looks to be hangin low. I agree with the starboard... I'll bet when the mako is tilted up its nice and clear out of the water. Had to notch out the top to accomadate the motor tilt. Looks like he repowered with a used yammie...
__________________
1984 Step-Lift Cuddy&&1993 Johnson 200hp
|
 |
|
|
Hybrid Mode
