1987 140 V4 Looper Carb Question

[nymack66]

What is the correct carb for this motor ? Mine have the 4 plastic carbs. I have posted to pros on screamandfly no one seem to know the answer. The reason for my question is when I brought the engine the previous owner give me a set of "spare" carbs. I now observe the ones on my engine is 1 3/8 throat size, my "spare" is 1 5/16. My curiosity is of course which is correct ?

[THEFERMANATOR]

They should be the larger ones for the 140, but there are ALOT of variations on them. How many screws are in the butterflies? What are the numbers on the metal plates screwed onto them.

[nymack66]

Originally Posted by THEFERMANATOR

They should be the larger ones for the 140, but there are ALOT of variations on them. How many screws are in the butterflies? What are the numbers on the metal plates screwed onto them.

I have three screws on the butterflies.
On the carbs 1 3/8 the numbers stamped is 397907 & 397908

On the 1 5/16 the numbers are 398395 & 398393

Thanks Ferm

[THEFERMANATOR]

Originally Posted by nymack66

I have three screws on the butterflies.
On the carbs 1 3/8 the numbers stamped is 397907 & 397908

These 2 carbs are for 86 to early 87 140's. So chances are the other 2 if they are larger must be a partial set of the 86 200XP carbs. In 86 and a few of the 87 200 XP high performance loopers they used a MASSIVE set of carbs. I take it they are almost a straight shot through the air passage through the center of em, if so that is them.

[nymack66]

Originally Posted by THEFERMANATOR

These 2 carbs are for 86 to early 87 140's. So chances are the other 2 if they are larger must be a partial set of the 86 200XP carbs. In 86 and a few of the 87 200 XP high performance loopers they used a MASSIVE set of carbs. I take it they are almost a straight shot through the air passage through the center of em, if so that is them.

Ferm you are an freaking genus as always ! Hats off to you my friend..here is what I found on another post it matches everything I have, the Bozo of a mechanic installed these carbs on my engine last year I switched em back because I rebuild the original I thought I had a set of spares wrong !
Nice little detective work but it was worth it.
Thanks Guys


"it is a 1986 evinrude model E225TXCD with 1987 carbs on it, part number on metal plate of carbs state
(4 carbs have this)
398393
1537
mx 01 IL
(2 carbs have this)
398393
1537
mx 22 IL
the jets are 47 idle, 14 intermediate and 62d high."

[Skools Out]

those jets are right for an 87 J/E 225 both of my 87 225's have same jets

[THEFERMANATOR]

Originally Posted by nymack66

On the 1 5/16 the numbers are 398395 & 398393

Thanks Ferm

These 2 numbers are for an upper and lower 87 225, so chances are they are a mismatched set.

[nymack66]

Sorry for the mix up Ferm
What I meant was on EACH set of carbs (total of 4 ) (1 3/8 bore size) numbers stamped is 397907 & 397908
The other set of 4 carbs bore size (1 5/16 ) numbers are 398395 & 398393

[THEFERMANATOR]

Originally Posted by nymack66

Sorry for the mix up Ferm
What I meant was on EACH set of carbs (total of 4 ) (1 3/8 bore size) numbers stamped is 397907 & 397908
The other set of 4 carbs bore size (1 5/16 ) numbers are 398395 & 398393

I understood what you were saying, the first two numbers are the port and starboard carbs for the 86-early 87 140 as they were jetted differently on each side. The second set of numbers are for a completely different set of carbs as the upper 4 carbs are one number on the 225's and the lowewr 2 are another number. If you have those 2 numbers both attatched to one throttle body, then they are most likely a pieced together set. Also some of the early 86-87 225's if they were short shafts got the 200XP carbs. I would stick to the smaller of the 2 sets which are most likely what should be on it. IIRC 120 carbs are 1 1/8", so 1 3/8" should be 140's.