|
|
#1
|
||||
|
||||
Installing NFB Steering Helm
Hey guys,
I'm to the point where I've removed the old hydraulic steering and have run the new steering cable through the gunwale. * As I was getting ready to install the bezel and the helm, I noticed that the existing hole from the previous helm is too big for the new one. *I have to make the hole smaller. *What should I do? *I know one option would be to glass in the hole with plywood, but would that be smart? *All of the stress from the new helm would be placed right within the patch area. *Should I consider glassing along with a piece of aluminum going across that whole face of that section where the steering wheel goes? * Here's the hole as it exists now: 
__________________
 1990 Hydrasports 2000cc Vector with 96 200HP Oceanrunner. Saved by grace alone, through faith alone, in Christ alone http://www.providencerpchurch.com/ 
|
|
#2
09-26-2006, 08:02 PM
|
|||
|
|||
|
Re: Installing NFB Steering Helm
Grace, Hmmm - thats a tough one. An easy solution hasnt come to me yet - maybe someone else will figure it out. The way I see it - you would have to pull the whole dash console off. I would make a round disc of wood that is a tight fit to the existing hole. Then I would securely attach that to a backer plate. Then, the backer plate could be securely fastened to the inside of the dash console. Lag screws, epoxy and glass, etc for the secure fastening. Good luck.
__________________
'86 Cuddy (FICHT 150 on brkt) ------ 1988 V20 project in the garage
|
|
#4
09-26-2006, 09:39 PM
|
||||
|
||||
|
Re: Installing NFB Steering Helm
Hammer has the answer
__________________
I have been through some terrible things in my life, some of which actually happened.
|
|
#5
09-26-2006, 10:33 PM
|
||||
|
||||
|
Re: Installing NFB Steering Helm
Thanks guys!!! Starboard it is--easy enough...
__________________
1990 Hydrasports 2000cc Vector with 96 200HP Oceanrunner. Saved by grace alone, through faith alone, in Christ alone http://www.providencerpchurch.com/
|
|
#6
09-26-2006, 10:45 PM
|
||||
|
||||
|
Re: Installing NFB Steering Helm
BGO, here's another possibily. Teleflex has excellent customer sercive. I'd bet if you call and ask that they have an adapter of some sort that will make your installation a bolt in. Probably even cheaper than Starboard and might look pretty slick.
Airslot
__________________
Airslot Airslot's V-20 Gallery
|
|
#7
09-26-2006, 10:56 PM
|
||||
|
||||
|
Re: Installing NFB Steering Helm
If Teleflex doesn't come through, how about a nice piece of round teak bigger than the hole???
something like this; 
__________________
http://img.photobucket.com/albums/v2...tz/captain.gifhttp://img.photobucket.com/albums/v2.../2sharkfin.gif&&&&SOMEWHERE IN TEXAS A VILLAGE IS MISSING THEIR IDIOT!
|
|
#9
09-26-2006, 11:55 PM
|
||||
|
||||
|
Re: Installing NFB Steering Helm
bygrace i've got what you need will get pics tomorrow. it's a steering adapter for your app. send a pic of the steering to my email of your steering pump you took out and a pic of the new steering box i'll see which adapter you need have a box of new ones.
__________________
 1978 V20 Cuddy w/ 225 Johnson. And Several other boat's
|
|
#10
09-27-2006, 12:47 AM
|
||||
|
||||
|
Re: Installing NFB Steering Helm
Thanks Skools!!! I'll send the pics tomorrow.
__________________
1990 Hydrasports 2000cc Vector with 96 200HP Oceanrunner. Saved by grace alone, through faith alone, in Christ alone http://www.providencerpchurch.com/
|
 |
|
|
Linear Mode
