|
|
|
|
#3
03-02-2005, 12:19 PM
|
|||
|
|||
Re: Rod Holders
I've been wondering about this myself. *I'd really like to know what arrangement others have used. *I'm converting to flush mounts too. *Photos would be great!
I'd like to have a rod on each side that sticks straight out, but it seems like the angle can't be too sharp if the holders are above the port and starboard inserts.
__________________
Olivia Grace - 1980 Stern Drive Cuddy 
|
|
#4
03-02-2005, 12:31 PM
|
||||
|
||||
|
Re: Rod Holders
That was another advantage of takin' out the original saddle tanks...it allowed flush-mount rod holders, so now it's got 4...2 on each side, ones in back point straight back, ones mid-ship are turned out some ...it's a pretty standard set-up...
The 30 degrees IS what you want...I'm tryin' to visualize what you gonna do w/that 5th rod holder?... Fillet, when you mount 'em be sure to use backing plates if at all possible... ;)
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#5
03-02-2005, 01:22 PM
|
|||
|
|||
|
Re: Rod Holders
My guess for the 5th rod holder is what I'm doing this spring: on my full transom it will hold my bait cutting tray leaving the other four holders to do their jobs.
__________________
1984 248 Sportsman w/1999 5.7L EFI Mercruiser 2001 Carolina Skiff J16 w/2005 25hp Yamaha tiller control
|
|
#6
03-02-2005, 01:28 PM
|
||||
|
||||
|
Re: Rod Holders
Yeah, havin' a full transom's got all kinds of advantages... 8)
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha
|
|
#7
03-02-2005, 01:51 PM
|
||||
|
||||
|
Re: Rod Holders
CT -Bingo!
I have a plastic holder in the center of the transom now, and the metal gimbal on the bait board is going to kill that thing in short order. So the 5th is a replacement. The full transom is a good place for the bait board, cause there really isnt much room off the back of the boat to drift lines, etc with the Armstrong bracket and swim platform. I already have two perko holders in the gunnels just aft of the rod boxes. They have caps as they drain into the hull. When I add the new ones, I'll have three in each gunnel. The new holders will probably be positioned over my new rod boxes, so I'll have to cut holes in them to allow the ends to poke through. Cliff paul - if you want two rods to stick out perpendicular to the boat, pick up a pair of rod riggers. I think Reliable makes them.
|
|
#9
03-02-2005, 03:35 PM
|
|||
|
|||
|
Re: Rod Holders
yeah, yeah, rub it in fillet. see the post I left you in the modifications section about your chart holder ;D
__________________
1984 248 Sportsman w/1999 5.7L EFI Mercruiser 2001 Carolina Skiff J16 w/2005 25hp Yamaha tiller control
|
|
#10
03-02-2005, 05:29 PM
|
||||
|
||||
|
Re: Rod Holders
I added some to the gunnels but they don't fit there all that well?? So I have some cheap flush mounts.
I need some desent ones!!
__________________
1986 V20  Old Fishermen never die, we just SMELL that way!!
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
