|
|
#1
|
||||
|
||||
Engine Mont
I took the old engine off the boat today, and hopefully will be bringning the hull to the marina some time next week for the new install. I assume the new enginges hole pattern will differ from the current one (86 Merc to a 2008 VTec) wwhat if enything should I do to the current mounting holes in the transom?
As always, thanks for your help!!! 
__________________
Last edited by Sean; 03-29-2008 at 08:03 PM. Reason: I cant spell 
|
|
#2
03-29-2008, 08:07 PM
|
||||
|
||||
|
The current holes should be fine. Nothing to worry about there...
__________________
 1990 Hydrasports 2000cc Vector with 96 200HP Oceanrunner. Saved by grace alone, through faith alone, in Christ alone http://www.providencerpchurch.com/
|
|
#3
03-29-2008, 09:16 PM
|
||||
|
||||
|
The mounting holes should close enough, but if they are not you'll need to plug the old holes before drilling the new ones. Some use 5200 in them to seal them up, but the reccomended method is to drive a piece of tight fitting wood through the hole, and then put a layer or 2 of cloth and resin over the wood dowels to completely seal it up. You could also use marine-tex, or make a filler compound with fiberglass resin and some silica dust or cavisil and put it in the holes like a putty. Check to see if your current holes will work first before doing any structural work.
__________________
2011 SUNDANCE B20CCR SKIFF, 2011 YAMAHA 90HP 4 STROKE, 2011 KARAVAN SINGLE AXLE ALUMINUM TRAILER, LOWRANCE ELITE-7 HDI, MINN KOTA RIPTIDE TROLLING MOTOR 2000CC HYDRA-SPORT 225+HP EVINRUDE SOLD  AND THE PINK JEEP!!!! R.I.P. http://www.wellcraftv20.com/communit...ad.php?t=11664 
|
|
#4
03-29-2008, 09:56 PM
|
||||
|
||||
|
My old boat needed me to relocate the holes. What I did was get a hard wood dowle and diped in resin and droveit in, when done I just soak small pieces of mat with resin and filled to level, then covered with marine tex for looks.
Easy fix! I think most motors to day are all the same. Unless you have a really old hull, my hull at the time was a 1965 with a 1973 Johnson, I put a 1990 Merc on at the time and holes were different.
__________________
1986 V20  Old Fishermen never die, we just SMELL that way!!
|
|
#6
03-30-2008, 05:59 AM
|
||||
|
||||
|
Won't hurt to ask them before they do the job.
__________________
Heavily medicated for your protection.
|
|
#8
03-30-2008, 08:18 PM
|
||||
|
||||
|
Quote:
__________________
2011 SUNDANCE B20CCR SKIFF, 2011 YAMAHA 90HP 4 STROKE, 2011 KARAVAN SINGLE AXLE ALUMINUM TRAILER, LOWRANCE ELITE-7 HDI, MINN KOTA RIPTIDE TROLLING MOTOR 2000CC HYDRA-SPORT 225+HP EVINRUDE SOLD AND THE PINK JEEP!!!! R.I.P. http://www.wellcraftv20.com/communit...ad.php?t=11664
|
|
#9
03-30-2008, 10:14 PM
|
||||
|
||||
|
If its close enough go there and bring a cardboard, put in and trace the holes go home and see if they match, Yes good, No fix befor it goes there. $100+ a hour for them to fix stuff!!
__________________
1986 V20 Old Fishermen never die, we just SMELL that way!!
|
|
#10
03-31-2008, 06:53 AM
|
||||
|
||||
|
when my e-tec was installed it lined up exactly with my 140 johnson
__________________
1987 Dual Console / 2007 200 hp E-Tec 
|
 |
|
|
Linear Mode
