|
|
#1
|
|||
|
|||
Will It Work
Ok guys, getting a small amount of change back from Uncle Sam. Before I buy this and make another mistake like I did with my bow lights, I want to make sure that this will work. So will it ??? Good points, bad points, dont buy it and just go out and get a Bayliner or what. ;D
__________________
|
|
#2
04-14-2007, 07:46 AM
|
||||
|
||||
|
Re: Will It Work
Looks like it will suit your needs diving and all. For me it's more crap to hang on the boat. I've removed bowrail and other "unnecessary" crap on mine.
__________________
 '75 Cuddy with '00 Johnson Ocean Pro 150 horse Benny
|
|
#3
04-14-2007, 08:45 AM
|
||||
|
||||
|
Re: Will It Work
Looks good, whats the leanth? You don't want it to short, you like it to go back on the puplit some for better levrage on the bow.
See thats what I wish I had got a Launcher style, But I didn't know that they had them till some one here posted a pic. But be careful to get the right one!! Don't get the roller for the rear of the boat, make sure they have and you get the front rolling type!!!!!!!!!!
__________________
1986 V20  Old Fishermen never die, we just SMELL that way!!
|
|
#4
04-14-2007, 10:16 AM
|
||||
|
||||
|
Re: Will It Work
Hammer, stop it, your getting me all worked up. *I've got the money sitting on my desk for this next project. ;)
I love that roller, but does anybody sell it in the USA? Who makes it. I can't find any info on it other than EBAY, west coast of Cananda...
__________________
Airslot Airslot's V-20 Gallery
|
|
#5
04-14-2007, 12:11 PM
|
||||
|
||||
|
Re: Will It Work
As long as your anchor SHAFT will fit between the front roller and the horizontal pin above the roller, that looks like it'll work great...looks well made...you'll still have to feed chain, rope over back roller as it plays out, but that's no big deal...will you use a chain tensioner or bungee to keep anchor in stored position?...bungee (good ones and keep an eye on those) is fine IMO ;) 8) ...
Took picture of choc Krispy Kremes and hot coffee for ya this mornin', only to find new drive disallowed... :P ... ...and I don't consider those lights a mistake...may notta been zackly what ya had in mind, but they'll look/work good where ya pictured 'em last nite ;) 8) ...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#7
04-14-2007, 03:18 PM
|
|||
|
|||
|
Re: Will It Work
Dont be surprised if I put you guys to work over the weekend when you guys stop by for the weekend in June. ;D
Air, spoke to the guy who has the starboard, says for another 10 or 15 bucks, he will cut and finish the sides. Not too bad at all on prices.
__________________
|
|
#8
04-14-2007, 03:37 PM
|
||||
|
||||
|
Re: Will It Work
Check you pm's Hammer...
__________________
Airslot Airslot's V-20 Gallery
|
|
#9
04-14-2007, 03:39 PM
|
|||
|
|||
|
Re: Will It Work
Hey Airslot, here's another one, but longer. This is 20" long. 100 bucks. That is with shipping . Not sure whats better, the longer one or sjorter one. Thinking the shorter one might be better since the pulpit is only 22 3/4" long. Going with the longer roller only gives you a few inches of play to have room for the chain tension clamp. Unless you exstend the anchor roller farther out over the edge of the pulpit. Any input *???
 http://cgi.ebay.com/ebaymotors/BRAND...QQcmdZViewItem
__________________
|
|
#10
04-14-2007, 03:48 PM
|
||||
|
||||
|
Re: Will It Work
I'm trying to find measurements on the other one now.
I'm also trying to get out on the V at 3 ;D
__________________
Airslot Airslot's V-20 Gallery
|
 |
|
|
Linear Mode
