Forum: Modifications
07-04-2021, 08:28 AM
|
|
Replies: 7
Views: 382
|
|
Forum: Classifieds
12-17-2017, 08:48 PM
|
|
Replies: 30
Views: 2,228
ok so I made it out yesterday and hit 5400 rpm...
ok so I made it out yesterday and hit 5400 rpm and 32 mph with the throttle hammered . I thought about it last night and this morning I adjusted the throttle cable at the motor. I couldn't adjust it...
|
|
Forum: Classifieds
12-11-2017, 08:50 PM
|
|
Replies: 30
Views: 2,228
|
|
Forum: Classifieds
12-03-2017, 09:03 PM
|
|
Replies: 30
Views: 2,228
|
|
Forum: Classifieds
12-03-2017, 07:34 PM
|
|
Replies: 30
Views: 2,228
ok ... so I went and talked to the guy at the...
ok ... so I went and talked to the guy at the prop shop and he said I wanted the top end RPM's in the specified range . On my Johnson 140HP 4 stroke the manual says full throttle range is 5600 to...
|
|
Forum: Classifieds
11-30-2017, 09:54 PM
|
|
Replies: 30
Views: 2,228
My prop is 15x21 ..What would be the benefit of...
My prop is 15x21 ..What would be the benefit of the bigger slower prop ? I think i'm going to go by the prop shop tomorrow . The top end at 30 hasn't really bothered me though ..it seems like im in...
|
|
Forum: Classifieds
08-31-2017, 10:09 PM
|
|
Replies: 30
Views: 2,228
|
|
Forum: General
12-29-2015, 05:48 PM
|
|
Replies: 718
Views: 35,978
Im with ya on the budget ..Im using polyester...
Im with ya on the budget ..Im using polyester also ..im buying my materials from Eastern Burlap
I was about to glue and tab down one stringer this weekend but chickened out after reading all...
|
|
Forum: General
12-28-2015, 11:05 PM
|
|
Replies: 718
Views: 35,978
|
|
Forum: How To
08-17-2015, 07:37 PM
|
|
Replies: 4
Views: 501
|
|
Forum: How To
08-17-2015, 07:36 PM
|
|
Replies: 4
Views: 501
|
|
Forum: How To
08-16-2015, 09:28 PM
|
|
Replies: 4
Views: 501
stringers ..bond to hull ? or leave gap ?
Guys , I'm replacing the transom (done) now on to stringers . In demoing them I notice there is a gap between the core and the hull . They are not glued down in any way . I've been reading as much as...
|
|
Forum: Repairs
05-08-2015, 10:45 PM
|
|
Replies: 7
Views: 337
thanks guys !it seems to be hardening up .. I...
thanks guys !it seems to be hardening up .. I was worried there for a little while .. I read somewhere after I did it to be sure to mix the resin and hardner first because the silica absorbs it and...
|
|
Forum: Repairs
05-08-2015, 05:26 PM
|
|
Replies: 7
Views: 337
Thickening Polyester with Silica question
Hi guys I have a question ..How bad did I screw up if I mixed silica and resin before adding the MEKP ? Its been 3 hours and doesn't seem to be hardening like previous batches that were mixed with...
|
|
Forum: Off Topic
03-06-2014, 08:34 PM
|
|
Replies: 9
Views: 277
|
|
Forum: Modifications
10-29-2013, 07:36 PM
|
|
Replies: 15
Views: 1,004
|
|
Forum: Modifications
10-21-2013, 08:37 PM
|
|
Replies: 15
Views: 1,004
|
|
Forum: Modifications
10-20-2013, 09:31 AM
|
|
Replies: 15
Views: 1,004
MJ , I like that seat ... dont you have to lean...
MJ , I like that seat ... dont you have to lean forward to steer ? That exact seat or something very close is what i'm after but what about how close your face is to the top of the wind shield when...
|
|
Forum: Modifications
10-19-2013, 10:54 PM
|
|
Replies: 15
Views: 1,004
1974 V20 cuddy console modification
Hello V20 gods ... I was given a 1976 V20 Cuddy back in August and planning on restoring her .. I like the whole set of this boat except the height of the steering wheel . I've searched this site and...
|
