|
|
#41
|
||||
|
||||
Sweet engine, looking forward to hearing about the sea trial.
__________________
1985 Wellcraft V-20, Evinrude ETEC 150: SOLD 1979 Marine Trader 44, twin Ford Lehman 120s 2006 Panga 14, Tohatsu 20 
|
|
#43
07-05-2015, 01:01 PM
|
|||
|
|||
Got the engine fired up today! Sounds great on the hose at idle!!! Getting closer one tiny step at a time!! Still finishing up wiring does anyone know if there are several wires not used in the engine harness on these efi engines or are they repurposed? Like choke, magneto kill wire ect? I mean I can start it and shut it down but have a few wires that don't seem like they would go anywhere looking at a generic diagram.
__________________
1983 wellcraft v20 steplift Mercury 250efi on the bracket!!!!
|
|
#44
07-06-2015, 07:05 AM
|
||||
|
||||
|
Glad to see some good progress. It should run out at a fairly brisk pace. What prop are you gonna try first? 19 Mirage should be near perfect. Sounds good, post that video up...
__________________
 1996 -19' NV Flats 115 Mercury 4-stroke 1983 -20' Wellcraft Center Console 250 XS
|
|
#45
07-06-2015, 05:15 PM
|
|||
|
|||
|
I'll put together a better vid and post it when I get back working on it! I've got a 21p prop right now and I'm gonna try it first... Hopefully it will be pretty close otherwise I'll be saving for a new prop also. What prop were you running on this engine when it was on your boat?
__________________
1983 wellcraft v20 steplift Mercury 250efi on the bracket!!!!
|
|
#46
07-07-2015, 10:52 AM
|
||||
|
||||
|
I ran a 21P Thunderbolt (Mirage Copy) and a 23P Tempest with vent holes for holeshot (signature picture) When I switched from your 250 EFI to the 250 XS I lost about 3 MPH. I took a old Tempest 25P and had it customized to get my MPH back. They knocked some of the pitch out and cleaned up the edges. I think I would try what you have first. It had ought to be close. When in doubt, trim it out...
__________________
1996 -19' NV Flats 115 Mercury 4-stroke 1983 -20' Wellcraft Center Console 250 XS
|
|
#47
10-01-2015, 07:04 AM
|
||||
|
||||
|
Updates? You get this rig finished?
__________________
1996 -19' NV Flats 115 Mercury 4-stroke 1983 -20' Wellcraft Center Console 250 XS
|
|
#48
10-01-2015, 08:22 PM
|
|||
|
|||
|
Nah bud not quite finished yet... Had a lot of stuff come up I've had to take care of the last few months with family and work. I actually started back on it a couple weeks ago. Have the hydraulic steering installed and bled now. Bought a set of used Lenco trim tabs for $10 that I've installed all but the switch. I've started cutting the panels that will fill the area where the I/o once was. I really don't have much further to go at all! Just have wiring and reinstalling bilge pumps and things of that nature. Only thing I'm up against now is me and the wife are going on vacation at the end of the month for a week and a half to see her family in Cali. Going to work on it some more this weekend but not sure if the maiden voyage will be before the vaca or if it will have to wait till after. Once I get this thing on the water we'll have to meet up so you can see the finished product! I think it's coming together quite well!
__________________
1983 wellcraft v20 steplift Mercury 250efi on the bracket!!!!
|
 |
|
|
Linear Mode
