|
|
#11
|
||||
|
||||
Re: Fiberglassing tools
I no have the fancy tools likem you guys, but thats what I use, palm sander, works great!!
leave the paper off and I will tell you, makes a great rub out toy also :-*
__________________
1986 V20  Old Fishermen never die, we just SMELL that way!! 
|
|
#12
03-30-2007, 11:47 PM
|
||||
|
||||
|
Re: Fiberglassing tools
I would think a disc-sander on a drill-motor and a good palm-sander would yield a pretty good job...long as ya keep that disc under control :o ...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#13
03-30-2007, 11:49 PM
|
||||
|
||||
|
Re: Fiberglassing tools
Quote:
Yeah...I like it w/ 80 GRIT and plugged into 220 :o ...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha
|
|
#14
03-31-2007, 12:10 AM
|
||||
|
||||
|
Re: Fiberglassing tools
hey I Love my air tools I have all air tools. I say air if you have a compressor. I run all mine on a 120 gallon 8 hp compressor usually @195 PSI. I couldn't make it without my air tools. much cheaper tools. Air DA is $7.99 from Harbor Freight. Plus you'll need a line sander if you plan on major work. never seen to many electric line sanders, they are $19.99 from HF as well.
Heck i found this compressor an it only needed the reeds cleaned. It's a Freebie and works great and will keep up with my Air DA sander. 
__________________
 1978 V20 Cuddy w/ 225 Johnson. And Several other boat's
|
|
#16
03-31-2007, 01:05 AM
|
||||
|
||||
|
Re: Fiberglassing tools
I have a 30 gal 6 hp craftman compressor, I have impack, hammer, die grinder, rachet ect ect ect, I love them.
__________________
1986 V20 Old Fishermen never die, we just SMELL that way!!
|
|
#17
03-31-2007, 01:16 AM
|
||||
|
||||
|
Re: Fiberglassing tools
lol yeah you know your Gravely's There Phat i have 2 1969 Gravely 7.6 Model L's best part they are in sequence serial numbers. my grand dad bought them new. I wish i had more attachments, i only have the rotary plow, 46" sickle bar, 42" bush hog, 48" snow / dirt blade, cultvator plow, steering sulky, and ditch trencher.
__________________
1978 V20 Cuddy w/ 225 Johnson. And Several other boat's
|
|
#18
03-31-2007, 11:03 PM
|
||||
|
||||
|
Re: Fiberglassing tools
unless you have a big compressor, tools like sanders and grinders will wear a compressor out( or your eardrums if its too close to you), I have a lot of air tools and they all have their time and place, but I've found on gell(except for the sprayer) and glass work, its hard to beat electric
|
|
#19
04-01-2007, 10:20 AM
|
||||
|
||||
|
Re: Fiberglassing tools
We were gravely dealers from 69 till 84. my dad had a small engine shop. i had a 7.6 until someone stole if from the barn last year. great engines. they went downhill when they started putting the kohlers on. i had the 30" bush hog & rotary tiller. tuff pieces of equipment....
|
|
#20
04-01-2007, 03:04 PM
|
||||
|
||||
|
Re: Fiberglassing tools
yeah those old 7.6 were Studebakers motor. I really want an old 816 Gravely Rider that has front and rear PTO for the old Model L attachments
__________________
1978 V20 Cuddy w/ 225 Johnson. And Several other boat's
|
 |
|
|
Linear Mode
