|
|
#12
05-18-2006, 07:38 PM
|
|||
|
|||
Re: Transducer mount, chines and step hull?.?.
I'll test it this weekend in the same position macojoe and most others use, and will post results. Sounds like it should be fine there.
__________________
'72 CC Picture Gallery 
|
|
#13
05-18-2006, 10:12 PM
|
|||
|
|||
|
Re: Transducer mount, chines and step hull?.?.
very interesting thread. be a while b4 i ready to install electronics but, i think this will help in the future. tx guys
|
|
#14
05-19-2006, 07:21 AM
|
||||
|
||||
|
Re: Transducer mount, chines and step hull?.?.
Rob...guess I'm gettin' old...FF ducer IS on 1st step from keel...sorry... ::)...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#15
05-19-2006, 08:43 AM
|
|||
|
|||
|
Re: Transducer mount, chines and step hull?.?.
No problem. Thought it was a typo. Would have been great if it worked that high.
__________________
'72 CC Picture Gallery
|
|
#16
05-19-2006, 10:19 AM
|
||||
|
||||
|
Re: Transducer mount, chines and step hull?.?.
It might...I never tried it there, though...why do you wanna put it there?...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha
|
|
#17
05-19-2006, 11:06 AM
|
|||
|
|||
|
Re: Transducer mount, chines and step hull?.?.
If it worked that high, it could be placed lower, between the steps on the angled portion of hull, and it would perform even better because step would not be disturbing the water flow.
I am guessing the hull rides on the steps at various speeds, so when wide open, only lower step remains fully in the water?
__________________
'72 CC Picture Gallery
|
|
#18
05-19-2006, 12:10 PM
|
||||
|
||||
|
Re: Transducer mount, chines and step hull?.?.
These V-20s aren't bass-boats ;) ...haven't looked w/ that particularly in mind, but my bet is the entire transom's in the water, chine to chine ;) :D :D ...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha
|
|
#19
05-21-2006, 11:28 AM
|
|||
|
|||
|
Re: Transducer mount, chines and step hull?.?.
Saturday tests results were not good with transducer on lowest starboard step. Below 12MPH, bottom would correctly show 6' to 11' but above that speed and it would start to jump up to 800' or more, even though still in 6' to 11' of water. Raised, lowered, adjusted tilt, angle, internal settings, still not good.
Will move between first and second steps and test that today.
__________________
'72 CC Picture Gallery
|
|
#20
05-21-2006, 10:47 PM
|
||||
|
||||
|
Re: Transducer mount, chines and step hull?.?.
Here is where mine is mounted, at this position it works great at all the speeds I've achieved. Bill Mc ;D
__________________
 Now being pushed with the Force of an E-Tec! http://www.wellcraftv20.com/gallery/...1990-V20-Sport http://www.youtube.com/watch?v=9ESnJm4uxug
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
