Wellcraft V20 Community

Go Back   Wellcraft V20 Community > Wellcraft V-20 Forums > Repairs

Reply
 
Thread Tools Display Modes
  #1  
Unread 04-07-2018, 08:16 PM
SkunkBoat's Avatar
SkunkBoat SkunkBoat is offline
God
 
Join Date: Mar 2010
Location: Manasquan Inlet, NJ
Posts: 1,913
Send a message via ICQ to SkunkBoat
Default

Fuses should be near the power source because the purpose is to protect the wire from burning if there is a short circiut.

If a fuse is 15 ft from the battery and the wire damaged and shorted to the negative (ground)between the battery and the fuse, then the wire is unprotected and will burn.

If you are going to run a Pos & Neg back to the battery for every circuit then the fuses should be within 7 inches of the battery. This becomes a mess of wires and fuses when you have 2 ff/gps, a VHF, running lights, stereo, horn, wipers,12v Acc socket (cig lighter)...

Often the instructions for electronics tell you to run separate wires and fuse all the way to the battery. This is for their benefit because it rules out the unknowns about your boat wiring if you call them and say it doesn't work.

If you are going to run a Pos & neg feed (8 awg) to a fuse panel under the dash then you need to protect the positive feed with a fuse at or near the battery with a 30A fuse. That panel then, in essence, becomes a power source and the separate circuits are appropraitely fused at the panel.
__________________
1984 V20 "Express" & 2003 Suzuki DF140 (SOLD!)
2000 GradyWhite 265 Express

YouTube/SkunkBoat https://www.youtube.com/channel/UC4F...znGospVOD6EJuw

Transom Rebuild https://www.youtube.com/watch?v=EEz94NbKCh0
https://www.youtube.com/watch?v=Oe_ZmPOUCNc
Reply With Quote
  #2  
Unread 04-08-2018, 10:27 AM
SkunkBoat's Avatar
SkunkBoat SkunkBoat is offline
God
 
Join Date: Mar 2010
Location: Manasquan Inlet, NJ
Posts: 1,913
Send a message via ICQ to SkunkBoat
Default

Another way to go on a small boat is to put a fuse block and ground bus near the battery if you have a protected area. At least that way you can use blade fuses (ATO) instead of glass fuses. Much easier to identify and replace. You'll still have a lot of wires but it can be organized better than a bunch of ring terminals on a battery.
__________________
1984 V20 "Express" & 2003 Suzuki DF140 (SOLD!)
2000 GradyWhite 265 Express

YouTube/SkunkBoat https://www.youtube.com/channel/UC4F...znGospVOD6EJuw

Transom Rebuild https://www.youtube.com/watch?v=EEz94NbKCh0
https://www.youtube.com/watch?v=Oe_ZmPOUCNc
Reply With Quote
  #3  
Unread 04-08-2018, 02:14 PM
steplift20 steplift20 is offline
God
 
Join Date: Nov 2004
Location: Beautiful New Jersey the high taxes state
Posts: 3,042
Default

Thanks guys ,that's what I thought Near the battery end I just wanted to confirm it cause I was not 100 percent sure, I knew you guys would come thru with the right answers, you always do Thanks again. And just in case you are thinking of getting a steering knob I bought one on Amazon for 12 bucks and it's real nice but the bracket didn't fit over my cushioned steering wheel so I had to make one It works fine ,on land lol Hopefully it will work on the water, only time will tell
__________________
love to fish
Reply With Quote
  #4  
Unread 04-08-2018, 03:56 PM
scook's Avatar
scook scook is offline
God
 
Join Date: Jul 2005
Location: Portland, OR
Posts: 1,432
Default

You don’t need any confirmation but here it is anyway - Skunk absolutely, completely nailed it with his comments and of course so did Destroyer.

I won’t comment on the padded steering wheel
__________________
Scott, Portland, OR '85 V-20 I/O, Merc 170
Reply With Quote
  #5  
Unread 04-08-2018, 03:58 PM
scook's Avatar
scook scook is offline
God
 
Join Date: Jul 2005
Location: Portland, OR
Posts: 1,432
Default

Oh, and Phat too.
__________________
Scott, Portland, OR '85 V-20 I/O, Merc 170
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:38 AM.


Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.