|
|
|
|
#1
|
||||
|
||||
I think he is talking about this "panel" looking place on the floor. I thought this was something that the caulk / screws could pulled out and remove the whole section. Is it just an indentation molded into the floor?
__________________
1994 V21 W/2002 130HP Yamaha 
|
|
#2
06-08-2012, 08:26 AM
|
||||
|
||||
|
Exactly.....indentation that says, "cut along here if you need to remove fuel tank." I thought V20's have a hatch?
__________________
 1994 Wellcraft V21
|
|
#3
06-08-2012, 04:04 PM
|
||||
|
||||
Oh... yep..100% solid fiberglass with wood glued to the bottom of it. But they never sealed the wood, so it rots out after it gets wet... And it will always get wet just from evaporation from the bilge... That's why so many V21's have the soft floor problem, especially up front in the helm area. <sigh>
__________________
1987 V20 w/1987 150HP Yamaha on a Shoreland'r Trailer 1978 16.5 Airslot w/1996 120HP Force on a Four Winns trailer 1996 V21 w/1993 200HP Mercury on a Shoreline Trailer All towed by a 5.7L Hemi Durango. If God didn't have a purpose for us we wouldn't be here, so Live simply, Love generously, Care deeply, Speak kindly. (Leave the rest to God)  Silence, in the face of evil, is itself evil. Not to speak is to speak, not to act is to act. God will not hold us guiltless.
|
|
#4
06-08-2012, 08:39 PM
|
||||
|
||||
|
Quote:
__________________
1986 V-20 1986 Yamaha 150 HP
|
|
#5
06-08-2012, 08:46 PM
|
||||
|
||||
Quote:
__________________
1985 Wellcraft V-20, Evinrude ETEC 150: SOLD 1979 Marine Trader 44, twin Ford Lehman 120s 2006 Panga 14, Tohatsu 20
|
|
#6
06-09-2012, 02:13 AM
|
||||
|
||||
|
Quote:
__________________
1987 V20 w/1987 150HP Yamaha on a Shoreland'r Trailer 1978 16.5 Airslot w/1996 120HP Force on a Four Winns trailer 1996 V21 w/1993 200HP Mercury on a Shoreline Trailer All towed by a 5.7L Hemi Durango. If God didn't have a purpose for us we wouldn't be here, so Live simply, Love generously, Care deeply, Speak kindly. (Leave the rest to God) Silence, in the face of evil, is itself evil. Not to speak is to speak, not to act is to act. God will not hold us guiltless.
|
|
#7
06-11-2012, 08:49 AM
|
||||
|
||||
|
Rob, I'm ok with the "happy" curved windshield but access to the fuel tank is pretty much non-existent!
Ain't cutting this floor unless it is soft. Will sell this SOB before I cut a perfectly good floor. 
__________________
1994 Wellcraft V21
|
|
#8
06-11-2012, 02:09 PM
|
|||
|
|||
|
Quote:
|
|
#9
06-11-2012, 02:24 PM
|
||||
|
||||
|
B - check out my thread in Repairs - Help removing hose barb from poly tank.....it explains why I needed better access to the tank. I've overcome all of those issues getting access, now I've pumped out the tank best I could - lots of trash in there. I am going to do some more pumping this evening.....even add a little clean gas and pump some more until I feel I've gotten most of the clutter out.....
Looking like my floor is safe from being cut - for now, thankfully!
__________________
1994 Wellcraft V21
|
|
#10
06-16-2012, 08:27 PM
|
||||
|
||||
|
Hey Destroyer, have a Q for you....when you installed the new floor did you leave a ledge around the outside edge of the floor bottom? and did you lay your wood on top of that edge and fasten down? I guess what I'm asking is how did you attach it down? I have my own ideas but wanted your advice....
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
