|
|
|
|
#1
|
||||
|
||||
Thinking about something like this.. http://www.bakatronics.com/shop/item.aspx?itemid=856
__________________
 1996 -19' NV Flats 115 Mercury 4-stroke 1983 -20' Wellcraft Center Console 250 XS 
|
|
#2
03-25-2012, 12:00 PM
|
||||
|
||||
|
Crickets-chirping.jpg
OK, I will go it alone. I am sure it will work. I will update with my findings..
__________________
1996 -19' NV Flats 115 Mercury 4-stroke 1983 -20' Wellcraft Center Console 250 XS
|
|
#3
03-25-2012, 01:59 PM
|
||||
|
||||
|
What if you find a simple reostat in the spec range?...that should give you the full range of control from hi to low...the Minn Kotas we use had speeds 1-10 and some guy came up w/a control box w/a reostat that gave infinite variable speed...it was a wired unit and worked very well for back then...I was about to buy one when the new Co-Pilot came out...couldn't resist.
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#4
03-26-2012, 12:27 PM
|
||||
|
||||
|
You reckon I can get an I-phone ap to do this?? HEEHee Haa Haa..
__________________
1996 -19' NV Flats 115 Mercury 4-stroke 1983 -20' Wellcraft Center Console 250 XS
|
|
#5
03-26-2012, 03:28 PM
|
||||
|
||||
|
Quote:
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha
|
|
#6
03-26-2012, 05:11 PM
|
||||
|
||||
|
Still looking at it. If I paid myself a nickel an hour for the research time I coulda bought a new one already. I think Kelly Controls is gonna be the answer to my dilemma.
http://kellycontroller.com/kds241001...ller-p-73.html Waiting on a response from Steven Li on a few issues like the momentary on and any additional resistors/flux capacitors that I may need. Looks good so far. I think the throttle is gonna be a slam dunk factory type retro-fit. Nice because I am not sure how salt-proof they are. At $19 I don't see it being a big problem. The control unit may need to be mounted in the semi-dry hatch directly under the motor. Might need to get rid of the foot switch too. I'll conjure something up and let everybody know what I got. 
__________________
1996 -19' NV Flats 115 Mercury 4-stroke 1983 -20' Wellcraft Center Console 250 XS
|
|
#7
04-16-2012, 07:30 AM
|
||||
|
||||
|
Went with the Kelly Controls KDS 24v 200Amp motor controller. It comes with plugs and pins to make wiring easy.
I attached it to the inside wall of the hatch under the lip for the best weather protection. trolling motor fix 008.jpg. I ordered the weatherproofing option for the controller for $15. The programming allows you to set input voltage on the low and high side for protection of the controller. Also delay on, high throttle bypass, throttle input, speed of throttle acknowledgement, percent of battery voltage output and a few other tricks. The controller wouldn't fit where the factory electrics were so extra wires had to be run from the throttle pot, on-off switch and LED light in the head to the control unit under the deck. Electric taped all the insulated signal wires to the power cable for now. Also incorporated my foot switch on the deck so it really is just like it was from the factory. Bottom line was around $200 from soup to nuts. But it works like a charm, fully variable, with a little dead spot at the beginning of the throttle that I was unable to program out. Decided to go with a little heavier controller after talking with Kelly, this one produces no heat that I could tell. Water test is next. I wanna see if the case ever heats up. The beauty is that the controller is one big heat sink, I doubt it will need any additional mass.
__________________
1996 -19' NV Flats 115 Mercury 4-stroke 1983 -20' Wellcraft Center Console 250 XS
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
