|
|
|
|
#1
|
||||
|
||||
Good job. I've been reading a couple of books about fiberglass work. Jerry Adams, the fella doing the work on my V20 said, Once you understand the basic principles, if ya can do a decent patch, you can build a 100 foot yacht.
__________________
1985 Wellcraft V-20, Evinrude ETEC 150: SOLD 1979 Marine Trader 44, twin Ford Lehman 120s 2006 Panga 14, Tohatsu 20 
|
|
#2
03-19-2012, 03:09 PM
|
||||
|
||||
|
Quote:
What book titles are you reading?... 
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#3
03-19-2012, 04:01 PM
|
||||
|
||||
|
Quote:
Fiberglass Boat Repairs Illustrated by Roger Marshall and The Fiberglass Boat Repair Manual by Allan H. Vaitses http://www.amazon.com/Fiberglass-Rep.../dp/0071549927 http://www.amazon.com/Fiberglass-Boa.../dp/0877422281
__________________
1985 Wellcraft V-20, Evinrude ETEC 150: SOLD 1979 Marine Trader 44, twin Ford Lehman 120s 2006 Panga 14, Tohatsu 20
|
|
#4
03-19-2012, 04:21 PM
|
||||
|
||||
|
Quote:
Thanks Bradford...those look pretty good... 
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha
|
|
#5
03-20-2012, 06:42 AM
|
||||
|
||||
|
I want some good reading material on modern techniques. Infusion, vacuum bagging etc. My local library didn't have squat.. Your glassman is right Bradford. I am sloppy with glass, to watch a pro do it for a while helps but it still takes a lot of skill to do a clean job.
Hatch looks great BTW..
__________________
 1996 -19' NV Flats 115 Mercury 4-stroke 1983 -20' Wellcraft Center Console 250 XS
|
|
#6
03-21-2012, 07:44 AM
|
||||
|
||||
|
Quote:
http://myweb.cableone.net/bcanderson...um/Vacuum.html http://www.bertram31.com/proj/tips/vaccuum.htm http://www.youtube.com/watch?v=sA8kIEbQ4uY Not books, but some info for ya!!...Google is full of this stuff...the only vacum bag I know about is the one my wife makes me change when it's full of dog hair...  Now if I can just figure out where it comes from... And now back to Thacker's original thread...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha
Last edited by reelapeelin; 03-21-2012 at 07:56 AM.
|
|
#7
03-23-2012, 10:44 AM
|
||||
|
||||
|
Great & timley post. I have a question, as I am getting ready to redo my fuel tank hatch. I noticed that you did not cut the access holes until after you glassed? I was thinking of cutting them first, so I could seal them up when I glassed. Interested to know your thoughts and/or what others have done. (i.e., Cut the access holes first and then glass or wait until after you glass?) Thanks, Jim
__________________
 1983 V20 Cuddy
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
