|
|
|
|
#1
|
||||
|
||||
Quote:
A canvas top would be much LIGHTER which is a certain consideration on any 20' boat...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#2
03-13-2012, 08:32 PM
|
||||
|
||||
|
Quote:
|
|
#3
03-13-2012, 09:46 PM
|
||||
|
||||
|
Proper primer for aluminum is zinc chromate. Two coats, first coat up and down, second coat side to side..that way there are no highlights. There are several other types also, including epoxies, but the US Navy uses zinc chromate ... and most of their equipment seems to get a lot of salt usage for some reason.
__________________
1987 V20 w/1987 150HP Yamaha on a Shoreland'r Trailer 1978 16.5 Airslot w/1996 120HP Force on a Four Winns trailer 1996 V21 w/1993 200HP Mercury on a Shoreline Trailer All towed by a 5.7L Hemi Durango. If God didn't have a purpose for us we wouldn't be here, so Live simply, Love generously, Care deeply, Speak kindly. (Leave the rest to God)  Silence, in the face of evil, is itself evil. Not to speak is to speak, not to act is to act. God will not hold us guiltless. Last edited by Destroyer; 03-13-2012 at 10:02 PM.
|
|
#4
03-14-2012, 05:26 AM
|
||||
|
||||
|
Quote:
|
|
#5
03-15-2012, 07:58 PM
|
||||
|
||||
|
I almost have the cap foundation complete and ready for fabbing the cap. here are some pics of the stern pieces i glued on lastnight and finished up tonight. I also included a picture of a piece of mocked up scrap plywood cap that i have been using to get all angles and dangles right. And notice the picture of my console with the free 27 gallon clear Moeller tank!!!!!! just got it yesterday for free from a buddy at work ,it was on his carolina skiff it has a sending unit and aluminum fittings Im stoked!!!! Its 3 inches narrower than the red 30 gallon tempo tank I bought 3 weeks ago. You will notice that the pic with the t-top that the bases on the top I bought are angle brackets!!! poor design!! alot of pressure in a very small area. Im gonna be putting new bases on it to fix that issue.
I also just wanted to pause for a minute a thank each and everyone of you on this site. All you guys have given me some great ideas and solid advice thru-out this build so far. This web site is awesome!!!!!
|
|
#6
03-19-2012, 09:56 PM
|
||||
|
||||
|
Grind,grind,sand,glass Grind, grind ,sand ,glass. Uh!!!!!! I'm gonna take s break this weekend and go taught fishing!
|
|
#7
03-20-2012, 07:46 PM
|
||||
|
||||
|
Here are some pics showing the way im glassing the rail before i fab and install the cap. The one pic of the transom shows some fairing and filling shaping and squaring up the transom lines.
|
|
#8
03-19-2012, 09:59 PM
|
||||
|
||||
|
Grind,grind,sand,glass Grind, grind ,sand ,glass. Uh!!!!!! I'm gonna take a break this weekend and go taug fishing!
|
|
#9
03-27-2012, 08:15 PM
|
||||
|
||||
|
Heres the cap supports I've been building. They are leveled up to the cap with a width of 8 1/2 inches. Another set goes up closer to the bow making a total of 3 per side. Give me your opinions on looks because it kinda looks wierd with the second one from the transom being high on the liner. They will all be glued, taped in and a progressive lap over the liner about 8 inches with 1708. Each support also gets 2, 4 inch stainless screws thru the rail also. Please tell me your opinions on design astheticly and structual. Thanks fellas
|
|
#10
03-14-2012, 06:12 AM
|
||||
|
||||
|
Quote:
Exactly what I did when I painted my half tower on my 236 Mako. Followed the 2 coats zinc chromate with 2 coats of Interlux Perfection.  Closer 
__________________
'78 V20 Center console "Sea Deez Nuts" 200 Merc Gloucester Pt, Va
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
