|
|
|
|
#1
|
|||
|
|||
WD-40 seems to work good on plastic too.
__________________
*************************************** Stay Safe!  Sold - 1984 V-20 Cuddy with a 2003 Johnson 140 hp gas sippin 4-stroke. 1995 Ranger 250C with a 2015 Suzuki 300 hp 4-stroke. 
|
|
#2
01-16-2012, 08:21 PM
|
||||
|
||||
|
There is a marine program at George Stone where i am taking welding. I am going to let them do carb kits on all the carbs and clean the bowls so hopefully there will be no more issues. After they do carb kits, they will put my outboard on the dyno and see what it puts out.
__________________
1983 V-20 capsized. . . . in the garage.
|
|
#3
01-16-2012, 10:47 PM
|
||||
|
||||
Quote:
__________________
1987 V20 w/1987 150HP Yamaha on a Shoreland'r Trailer 1978 16.5 Airslot w/1996 120HP Force on a Four Winns trailer 1996 V21 w/1993 200HP Mercury on a Shoreline Trailer All towed by a 5.7L Hemi Durango. If God didn't have a purpose for us we wouldn't be here, so Live simply, Love generously, Care deeply, Speak kindly. (Leave the rest to God)  Silence, in the face of evil, is itself evil. Not to speak is to speak, not to act is to act. God will not hold us guiltless.
|
|
#4
02-15-2012, 10:32 PM
|
||||
|
||||
|
Update
Found out i had low voltage on two plug wires, had carbs cleaned, a few electrical gremlins with the ignition, and the shaft mounts and steering shaft are shot. Motor had 92-94psi compression on all but one cylinder which had 82. If nothing else breaks when trying to repair it, it would cost over $1000 just for parts.
So i am having another motor installed this coming week, a 1986 Yamaha 150 25" shaft. I will build a jack plate, out of some 4x4 1/4" wall square steel tubing i have, so it will work on my 20" transom. Now i just need a remote control.
__________________
1983 V-20 capsized. . . . in the garage.
|
|
#5
02-15-2012, 11:31 PM
|
||||
|
||||
|
Jason I strongly suggest that you source some aluminum angle for your jackplate..... rust streaks are a real pain in debut.
|
|
#6
02-16-2012, 10:26 AM
|
||||
|
||||
Quote:
__________________
1987 V20 w/1987 150HP Yamaha on a Shoreland'r Trailer 1978 16.5 Airslot w/1996 120HP Force on a Four Winns trailer 1996 V21 w/1993 200HP Mercury on a Shoreline Trailer All towed by a 5.7L Hemi Durango. If God didn't have a purpose for us we wouldn't be here, so Live simply, Love generously, Care deeply, Speak kindly. (Leave the rest to God) Silence, in the face of evil, is itself evil. Not to speak is to speak, not to act is to act. God will not hold us guiltless.
|
|
#7
02-16-2012, 05:44 PM
|
||||
|
||||
|
This is just temporary to get me back on the water, I have found a hi-jacker fixed jack plate that lifts 5" and sets back 4" for $150. If everything works out i will purchase one. But i refuse to throw anymore money into this boat than i have to. Carb rebuild, new tilt/trim motor, and many many hours of tracking down problems with this motor and now this. I am done with it!
I will paint the steel jack plate with an epoxy paint after i get it welded up, to delay the rust for awhile. Like i said, once i get the Yammie on her and get confident again i will purchase an aluminum jack plate. http://www.wholesalemarine.com/p/T-H..._JP_d_4FA_d_DP
__________________
1983 V-20 capsized. . . . in the garage.
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
