transom rebuild help

[RidgeRunner]

Inside transom thickness from the factory on my V was thin (One layer of heavy woven into one oz matt). They didn't throw too much at it and they didn't spend any time filling in the gaps with putty to smooth out the transitions. To me 38 oz. sounds about right with what the factory used. I don't recall them using much if any reinforcement around the perimeter where the real loading is. The outside (hull) on mine was about 1/4" to 3/8" thick. You could debate for hours on the layup schedule. What Richie Rich said, thumbs up!! I personally like to layup wet on wet if two or more layers are used. If the 1st layer is allowed to kick off and set, you then have to grind it out again to get a proper bond(at least with VE, not sure about epoxy). So you would be grinding away some of the long woven strands in order to layup a second layer and that would deminish the strength of the first layer. When wet on wet isn't possible and where weight isn't a concern I like to lay a layer of 1.5oz mat into the roving as a sacrificial layer that can be roughed up for the second or third layers of glass. My .02
IMO what you have done so far looks great. You need to spend some time on the top of the transom to ensure it is waterproof. With respect to the heavy weight fabric, it is very difficult to get it to make the tight radius where the upper edge of the plywood core meets the upper lip of the transom. You may want to get some lighter glass to reinforce the edges and push into the corners at the top sides and bottom of the transom. You have come a long way fast. Don't rush it too much, take your time and the results will be spectacular.

[Richie Rich]

I'm surprised the inner skin was that thin....even more surprised that the outer skin was that thick....usually, the skins of a core are closer to being equal....I guess not with the wellcraft.....With epoxy, you don't need to grind the new glass...just sanding with 80 grit and a wipedown with alcohol will make it ready for a new skin, if needed.

[CharlestonSC]

Yes same on mine as outer skin was pretty thick and inner skin looked like what I am using but the gel coat they sprayed on it makes it look a tad thicker.
I think with thick epoxy I used to glue in the 2 3/4'' ply's and the extra tabs should be good but I do hang a 200hp off of this sport 20, so I might run a sheet where the motor bolts go and tie into the stringers and add a few more tabs to tie in more to the sides again.
I do want to beef this up as I do want to venture a few miles offshore.

On another note do you think I will have any issues adding a 30 gal tank directly in front of the original tank? There is an empty space that I want to add another tank to give me more distance for longer trips.

[Richie Rich]

My V has a plate on the inside where the motor is attached. It was put on by the shop where the previous owner had his boat maintained. The core is still ok, so I'm thinking there was a little flex issue. And its a 150 motor.

Anyway, if you're thinking about beefing it up at the bolt area and tabbing the corners, you might as well just run another sheet across the whole thing and come around the corners and be done with it....sanding a flat, wide area like that won't take much more time with a ROS and 80 grit.

And an additional tank?? You can probably fit one but you're getting to the "slim" area of the boat...not sure you'll have the room for 30 gallons...that's also another 240lbs of weight sloshing around the nose of the boat....not sure what that will do the the boats handling and balance...maybe someone else has done this already and has some feedback on how it went.

[CharlestonSC]

New picts, I added another 3/4'' piece in-between the stringers and attached it to the transom, and added more tabs, I am waiting to get more epoxy resin in to do a big sheet across the back. This should make it strong as ever.
I also was able to add another 30 gal Moeller tank directly in front of the old tank, as I cut a few access holes in the floor that I just reglassed but they will be under the console.

[RidgeRunner]

Nice, glad you added some more glass. Now tough as nails/never need to worry with it again. You have a bulkhead that I didn't have on my 1983, just in front of the fuel tank. I installed a 13 gallon fresh water tank and pump there. No ill effects on handling that I could see. I moved some weight up front for the addition of a bracket, hoping the balance was right. Is there enough room to run the fill and vent lines under the liner? or are you going to do something else?

[CharlestonSC]

Originally Posted by RidgeRunner

Nice, glad you added some more glass. Now tough as nails/never need to worry with it again. You have a bulkhead that I didn't have on my 1983, just in front of the fuel tank. I installed a 13 gallon fresh water tank and pump there. No ill effects on handling that I could see. I moved some weight up front for the addition of a bracket, hoping the balance was right. Is there enough room to run the fill and vent lines under the liner? or are you going to do something else?

Yes as you see the bulkhead inbetween is about 3'' lower than the deck, then there is a big cut out in the stringer on starboard side which both gas fills and vents will fit.