prop survey

[Skools Out]

oh just bumped it so a friend could find it. plus to read threw it again.

[RidgeRunner]

Very nice. 1983 20'CC
2.4L 200HP Merc- 48mph @ 6100RPM- 14.5x17pQuicksilver light load
2.4L 200HP Merc- 46mph @ 5800RPM- 15.5x17P Mirage light load
3.0L 250HP Merc-63mph @ 5800RPM- 15.5x23p Tempest light load
3.0L 250HP Merc- 55mph @ 5800rpm- 15.5X23P Tempest heavy load
3.0L 250HP Merc-58mph @ 5800RPM- 15.5x21p Thunderbolt heavy load

3.0L 250HP Merc- ??? @ ??? - 15.5x25P Tempest light
Last try with a different prop, just as soon as I get my new lower unit
Then the fuel sippin 2.4 goes back on.

[whatknot]

Here's tested props. Didn't have a 17 to test....

1985 Wellcraft v20 Fisherman CC
Closed Transom with Stainless Marine Bracket
Yamaha F150

Fuel topped off at 60 Gallons
2 batteries (unfortunately in the stern)
Full 20 gallon in deck livewell (unfortunately in the stern)
Boat is a tad bit *** heavy....

Prop RPM MPH GPH

Mercury Vengeance
14.5 x 15 -5700- 36 - 14.2
Cruise - 4260 - 24.4 -8.7
4.5 seconds to plane


Yami 3 blade SS Black (old)
13.5 x 19- 5600 - 36.2 -16
Cruise - 3800 - 25.4 - 10
6 seconds to plane

Spoke with Power tech dude. He recommended a OFS3R15 3 blade 15 1/4 x 15

or a OFS4R14P (15 1/4 x 14) 4 blade.

Anyone running these dimensions for a prop and what do you think?

Thanks

i have a 85' c.c. repowered with a 99' 225 efi merc... this has been a project just finally putting on the pieces together. first run with a 13"x21p mirage wot 5100rpm 53.5mph----4000rpm 40 mph......2nd run 13"x17 quicksilver 5800 rpm 50.5 mph----4000 33.5mph.... waiting till this weekend to try a buddies 19p wheel hope thats where i need to be

[Genie Aye]

200HO E-tec

15x19 Rebel SS

5400 RPM

Light load--53.4 gps

average load--52.0 GPS

Cruise at 35mph at 3750rpm


Thinking about a 4 blade to create some stern lift with the heavier motor.

[tnltracy]

I have a 13-3/4 x 15 aluminum currently. Last year I was getting around 24MPH at 5500 RPM by GPS. Start of the year I was showing around 29MPH, but her butt got a bit dirty over the summer

At WOT, the motor would over rev well over 6k RPM, so I've been shopping for a new prop this year. I just picked up a used 13-1/4 x 17 that I'm hoping will take RPM's down a tad and give me a few more MPH's. Will report once the boat gets into the water

[kman104501]

I have a 19 pitch ss, not sure what dia, 225 Evinrude, WOT 50MPH after being in the water for 1/2 a season. Always wondered if it would pay to go slightly larger....

[Genie Aye]

Originally Posted by kman104501

I have a 19 pitch ss, not sure what dia, 225 Evinrude, WOT 50MPH after being in the water for 1/2 a season. Always wondered if it would pay to go slightly larger....

At WOT with a average load--what rpm are you at?

Rpm will tell you if you are prop'd right or not--you do not want to over prop for sure.

[Destroyer]

Originally Posted by rb437

Thanks,

Now a couple more questions -
1. How do I determine outdrive gear ratio?
2. Where's a good place to find a prop?

Rick

A few good places to find props (and other stuff):

http://www.boat-links.com/linklists/boatlink-30.html

http://www.outboard-motors.us/years/

http://forums.iboats.com/forumdisplay.php?f=21

And of course eBay is a great place to buy used props at a great price. I've bought several props that way and never been disappointed. Just do your homework beforehand so you know the type of material, the number of blades, the diameter and the pitch you want.
Then find a prop and compare it online to a new prop of the same type pricewise. A lot of times you can find really good deals. It's also a good place to find a servicable throwaway prop for not a lot of money. That way you don't invest hundreds and hundreds of dollars trying out a different diameter or pitched prop and then you decide you don't like it's performance after you've bought it.

Also, for repair of a prop I'd recommend:

http://www.thepropellershop.net/

Hope this helps a little ...

[kman104501]

Originally Posted by Genie Aye

At WOT with a average load--what rpm are you at?

Rpm will tell you if you are prop'd right or not--you do not want to over prop for sure.

I am able to get to 5600RPM without a problem with 3 people, full tank of fuel and fishing gear (of course).