|
|
|
|
#1
|
||||
|
||||
nice tanks what sizes
and lumber hate to tell ya but that ain't powercoat it has runs, powercoat doesn't run like that. looks like epoxy coat
__________________
 1978 V20 Cuddy w/ 225 Johnson. And Several other boat's 
|
|
#2
02-15-2010, 11:39 AM
|
||||
|
||||
See if you can post that part number to the links section for future use.
__________________
1985 Wellcraft V-20, Evinrude ETEC 150: SOLD 1979 Marine Trader 44, twin Ford Lehman 120s 2006 Panga 14, Tohatsu 20
|
|
#3
02-18-2010, 08:42 PM
|
||||
|
||||
|
I added another bulkhead just aft of the tank to help support it. then I added some foam to the bottom of the tank to support it and hold it in place. I also finished foaming in the fishbox. this new foam that I used really worked out great. The manufacturer is called hi bond. They sell it in gallons rather than quarts like the last stuff I used. Its cheaper too. The installation instructions for the tank say specificly NOT to foam in the tank because it needs to be able to flex 2-3%. That is why I did not fully foam it in. I actuall have to cut a little foam out because it expanded more than I thought it would.
|
|
#4
02-18-2010, 09:29 PM
|
||||
|
||||
|
Quote:
Your rite skools it was epoxy ... I know it will out last me tho 
__________________
1987 Dual Console / 2007 200 hp E-Tec 
|
|
#5
02-18-2010, 09:31 PM
|
||||
|
||||
|
Quote:
 I made one out of plywood but couldnt get it to hold any gas...
__________________
1987 Dual Console / 2007 200 hp E-Tec
|
|
#6
02-18-2010, 10:28 PM
|
||||
|
||||
|
looks good!! just becareful when using foam, i have know others to lift floors, warp hulls as it expanded to much.
but you sound like you know what your doing, keep up the good work!1
__________________
1986 V20  Old Fishermen never die, we just SMELL that way!!
|
|
#7
03-27-2010, 09:54 PM
|
||||
|
||||
|
well it's been a while but I got some more work done on the boat today. I cleaned up the underside of the floor. cut out some new wood. I glued it in with resin thickened with West System 403. then I added a piece of 1/4" aluminum where I will mount the drivers seat. Then I rolled on a layer of woven roving. I ran out of resin near the end so I will have to finish tomorrow. I need to get this done it has taken entirely too long.
|
|
#8
05-11-2010, 09:09 PM
|
||||
|
||||
|
the floor is finally in!!! It has been a very busy spring so far. getting any work done on my own boat has been hard to come by. But I'm almost done. I got a smoking deal on some underwater lights. More pics of them will be soon.
|
|
#10
05-12-2010, 05:46 PM
|
|||
|
|||
|
Can you explain the process used to pull out and repair the deck?
How hard is it to get the deck out once the perimeter is cut. Are there any mechanical fasteners to remove? When putting the deck back in, how is it fastened to the stringers? How is the gap from the saw blade repaired, filled? Curt
__________________
84' Wellcraft Fisherman 18 / 96' Evinrude 130-Sold 20' Fisherman project underway www.ParkerFenceandDeck.com
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
