|
|
|
|
#1
|
||||
|
||||
Wow!!...top of the line stuff ya got there, Rob...those REELY look GREAT!!...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#2
09-27-2009, 08:44 AM
|
||||
|
||||
|
Thems some of the best looking cupholders I've seen. Might have to get a set myself.
__________________
Heavily medicated for your protection.
|
|
#3
09-27-2009, 09:54 AM
|
||||
|
||||
|
RW did u use something to back the screws on the inside of the fiberglass?
__________________
Willy 1986 V20 Old School 1992 V20 1992 150 Yamaha 1997 HydraSport 2250 Vector 2009 17' G3 Outfitter "G Spot" http://www.youtube.com/watch?v=TDebw...eature=related "I won't be wronged, I won't be insulted and I won't be laid on a hand on. I don't do these things to others and I require the same from them" JW
|
|
#4
09-27-2009, 10:00 AM
|
||||
|
||||
|
Wow I like those cup holders I have the perfect spot inmind for a couple of those.
great work RW 
__________________
1987 Dual Console / 2007 200 hp E-Tec 
|
|
#5
09-27-2009, 10:41 AM
|
||||
|
||||
|
those things are sweeeeeet. I might have to put a pair of them on my boat too. Nice work!
|
|
#6
09-27-2009, 11:46 AM
|
||||
|
||||
|
Hey Wilson
Do they interfere with the rod holders? Where did you get them? thanks
__________________
Tis better to be quiet and thought a fool than open your mouth and prove it!! 1991 V-20 cuddy I/O 350 volvo duo prop, 1998 15ft Grumman 9.9 Johnson  
|
|
#7
09-27-2009, 12:23 PM
|
||||
|
||||
|
__________________
 '75 Cuddy with '00 Johnson Ocean Pro 150 horse Benny
|
|
#8
09-27-2009, 12:29 PM
|
||||
|
||||
|
Quote:
here's a link to where I posted them a few weeks ago.... man the rod holder almost got me....I checked and rechecked to make sure I was no where near steering cables/wires but forgot about the rod holders.. I cut the first hole and the rod holder was encroaching into the space by like 1/2" or less cutting across the top left hand corner. fortunately I cut the 4 corners of the fiberbglass out with a hole saw and I was able to push the hole saw in further and take a perfect crescent shaped piece out of the plastic tube of the rod holder, rods still fit in no problem. (if they were ss I would have been screwed. If I had only moved them back another 1/2" or so I would have had no problem...(turns out on the port side I did not have that problem as the rod holders are not installed identical on both sides (close but not exactly) Willy, I kind of half assed it, right now they are only screwed into the 1/4" or so fiberglass....my intention was to through bolt as I am pretty sure I can reach them from the aft hatches but I didnt have all the hardware and I had a nice supply of #10 screws. I had some free time yesterday (rare) so I just used sealant and screws. if they loosen up on me on I'll through bolt them with some nice fender washers or reinforce with some wood behind the hole.
__________________
1986 V-20 1986 Yamaha 150 HP
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
