|
|
|
|
#1
|
||||
|
||||
Soft deck plates, thats the gas tank cover, many many are soft!! Remove the whole panale and take all wood of, they will be small squares, you will replace with one sheet ply.
Transom is factory cut and you must have a 20" shaft motor. Might want to remove motor and take the Alum cap off and ck wood, if all is well, (sorry but I bet there if damage) then glass over sand and paint and seal forever, it the beast way. The floor is by far the worst fix, but cut it out till you ind good wood and start adding new ply. Save the skin of the floor so you just reglass it to the new wood.
__________________
1986 V20  Old Fishermen never die, we just SMELL that way!! 
|
|
#2
09-13-2008, 07:26 AM
|
|||
|
|||
|
That is the same transom that I have, it is factory and the cap on it is fiberglass. When I swapped engines I tried to take mine off but I think they used resin to put it on.....anyway, my transom was fine, I just sealed up the seams around it with 5200 (man I hate that stuff) and stuck on the new motor.
One thing I did have to do was grind a little on the cap where the steering arm is cause it was rubbing. I just put a little paint on it to keep it from sucking water in.
__________________
*************************************** Stay Safe!  Sold - 1984 V-20 Cuddy with a 2003 Johnson 140 hp gas sippin 4-stroke. 1995 Ranger 250C with a 2015 Suzuki 300 hp 4-stroke.
|
|
#3
09-13-2008, 07:27 AM
|
|||
|
|||
|
Oh, and in Miami, you will probably be able to get a good used OB out of some rich guys trashcan.
__________________
*************************************** Stay Safe! Sold - 1984 V-20 Cuddy with a 2003 Johnson 140 hp gas sippin 4-stroke. 1995 Ranger 250C with a 2015 Suzuki 300 hp 4-stroke.
|
|
#4
09-13-2008, 10:27 AM
|
||||
|
||||
|
Thanks for straightenin' me out, Ferm...and ain't pics wonderful thangs!!...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#5
09-13-2008, 01:34 PM
|
|||
|
|||
|
great thanks all.
I found some outboards on craigslist, will any of these blocks fit the one i have? I will take a picture of the engine block to show you all the hole it has on the block side. this one doesnt look like the engine i have http://miami.craigslist.org/mdc/boa/835511868.html This looks alot like the same model i have http://miami.craigslist.org/pbc/boa/838617227.html
|
|
#6
09-13-2008, 02:06 PM
|
||||
|
||||
|
With every engine manufacturer there will be subtile or gross differences in powerheads of the same horsepower, given the year models.
The possibility exists that the foot may be interchangable more readily than the powerhead. Each one is not running, you should be able to find one that runs for $1500.
__________________
 '75 Cuddy with '00 Johnson Ocean Pro 150 horse Benny
|
|
#7
09-13-2008, 02:12 PM
|
||||
|
||||
|
Looking to see what years might be interchangable, found one with your same problem.
http://madison.craigslist.org/boa/824271693.html 1992 Mercury 200 hp Outboard EFI Reply to: [email protected] [?] Date: 2008-09-02, 4:44PM CDT 1992 Mercury 200 hp Outboard EFI, blown powerhead. Engine not seized but there is a hole in the block behind the starter. Great lower unit/ trim tilt etc. $1000 608-332-6110 
__________________
'75 Cuddy with '00 Johnson Ocean Pro 150 horse Benny
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
