Wellcraft V20 Community

Go Back   Wellcraft V20 Community > Wellcraft V-20 Forums > Modifications

Reply
 
Thread Tools Display Modes
  #1  
Unread 05-25-2008, 07:09 PM
THEFERMANATOR's Avatar
THEFERMANATOR THEFERMANATOR is offline
God
 
Join Date: Dec 2006
Location: Zephyrhills Fl
Posts: 7,206
Send a message via AIM to THEFERMANATOR
Default

Quote:
Originally Posted by spareparts View Post
yeah none of the outboards have aircleaners(except Opti's), offer them $1000 cash, pending a compresion test, spark test, and check the gear lube. If they don't have anythign to hide, they should take it
They list the compression numbers in there ad, and they didn't look good to me. low side 110 and high side 135. They don't have air filters, but the air box is an important item to leave on them if they are jetted stock. They resatrict the airflow just slightly t o control the metering circuits in the carbs, and if you remove it on a stock engine it will cause it to lean out and burn a piston and cause a miss or lock-up. I wouldn't offer him a $1000 for an engine with compression numbers like he posted it has, let alone if it has a miss.

On the YAMAHA all of em prior to 94 had a steel shift shaft and they are known to rot in two and then you can't shift them. The repair can range from around $250 for the shift rod and base gasket on up depending upon what else you have to do at the time of the repair. If the bolts that hold the powerhead on are seized in then the repair can get expensive and labor intensive.
__________________
2011 SUNDANCE B20CCR SKIFF, 2011 YAMAHA 90HP 4 STROKE, 2011 KARAVAN SINGLE AXLE ALUMINUM TRAILER, LOWRANCE ELITE-7 HDI, MINN KOTA RIPTIDE TROLLING MOTOR

2000CC HYDRA-SPORT 225+HP EVINRUDE SOLD

AND THE PINK JEEP!!!! R.I.P.
http://www.wellcraftv20.com/communit...ad.php?t=11664
Reply With Quote
  #2  
Unread 05-27-2008, 10:36 AM
Geekie1's Avatar
Geekie1 Geekie1 is offline
Senior Member
 
Join Date: Jan 2006
Location: Doylestown PA, Cape May Co. NJ
Posts: 193
Default

If the 92 200 Yamaha was used in fresh water only, the shift rod has probably not corroded and it's not ready to break . It doesn't take alot of saltwater use to cause corrosion fast however. The 150, 175, and 200 Yamaha's are close to the same weight.

As far as reliability of early Yamaha V6's is concerned, they are about as simple and reliable as they get. The oil system is very simple and reliable. With the exception of the shift rod replacement, or power head removal (broken bolts) they are easy to work on. Rebuilding the water pump is very easy and I have been doing this repair for years. (about a 1.5 hr job)

I have had and still have Evinrude outboards and like them very much. However, I never owned an Evinrude or Johnson bigger than a three cylinder 70HP.

All in all, the Yamaha's I have owned have been the most reliable outboards by far. They are not the most fuel efficient, or fast, and they require regular preventive maintenance. But when I head out of the inlet to the open ocean, I am glad I have the Yamaha hung on my V's transom.

Geek
__________________
Doylestown, PA - Cape May County NJ, and all of the fishin\' holes known and unknown in the Delaware Bay and offshore!!!
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:33 PM.


Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.