Wellcraft V20 Community

Go Back   Wellcraft V20 Community > Wellcraft V-20 Forums > Off Topic

Reply
 
Thread Tools Display Modes
  #1  
Unread 01-14-2008, 12:38 AM
THEFERMANATOR's Avatar
THEFERMANATOR THEFERMANATOR is offline
God
 
Join Date: Dec 2006
Location: Zephyrhills Fl
Posts: 7,206
Send a message via AIM to THEFERMANATOR
Default

I know that I've worked on a couple of 248/250's, and the fiberglass seams under the water tank seem to be a trouble area with delamination. Water seems to come in from the anchor area and runs down in. As MJ said, watch Ebay for decals. As for the rod racks, we always just kept them on one of the quarter births when not in use.
__________________
2011 SUNDANCE B20CCR SKIFF, 2011 YAMAHA 90HP 4 STROKE, 2011 KARAVAN SINGLE AXLE ALUMINUM TRAILER, LOWRANCE ELITE-7 HDI, MINN KOTA RIPTIDE TROLLING MOTOR

2000CC HYDRA-SPORT 225+HP EVINRUDE SOLD

AND THE PINK JEEP!!!! R.I.P.
http://www.wellcraftv20.com/communit...ad.php?t=11664
Reply With Quote
  #2  
Unread 01-14-2008, 01:25 AM
jasoncooperpcola's Avatar
jasoncooperpcola jasoncooperpcola is offline
God
 
Join Date: May 2007
Location: Pensacola, FL
Posts: 1,467
Send a message via Yahoo to jasoncooperpcola
Default

Thanks, Ferm. We pulled the water tank out and are planning to use that area for our anchor rode storage. We are planning to put a hawse pipe for the rope to go through. Does anybody have any recomendations for an anchor roller. Wherever i mount the anchor roller its gonna have to be strong enough to break an anchor loose. I'll try to take a picture of the bow area of the 250 tomorrow. This is a picture of our curretn setup on our V20.
Attached Images
File Type: jpg IM000955.jpg (39.4 KB, 8 views)
__________________
1983 V-20 capsized. . . . in the garage.
Reply With Quote
  #3  
Unread 01-14-2008, 01:41 AM
macojoe's Avatar
macojoe macojoe is offline
Administrator
 
Join Date: Mar 2003
Location: Carver, Ma.
Posts: 15,859
Send a message via AIM to macojoe Send a message via Yahoo to macojoe
Default

I had a roller like shown in the picture, and was fine, once in a while the anchor would get stuck and you had to give it a little push.

Hamer and irslot bought tilting rollers, so when you undid the rope the weightof the anchor would tilt it down to the water and off she go real easy!!
If I decide to add one to thenewboat I will use a tilting roller.
__________________
1986 V20

Old Fishermen never die, we just SMELL that way!!
Reply With Quote
  #4  
Unread 01-14-2008, 07:25 AM
phatdaddy's Avatar
phatdaddy phatdaddy is offline
God
 
Join Date: Mar 2003
Location: south of I-10
Posts: 4,965
Default

Jason, you should be able to go to a local sign shop with a pic of the decals & they could reproduce them for you. if you can get a pic with a ruler in it. that will help.
Reply With Quote
  #5  
Unread 01-15-2008, 10:05 PM
Monkey Butler Monkey Butler is offline
Senior Member
 
Join Date: Aug 2005
Location: Central Mass.
Posts: 646
Default

Jason,

Do you have a forward bilge pump? If so is it in the compartment you are talking about? When I first got my Sportsman I saw where the forward pump was and said, why is that there? I couldn't see how water would get there. Then one time just after I hauled the boat out at the ramp I stopped short a a red light and looked in my side mirror to see a stream of water gushing out the side of my boat onto a car stopped beside it! Good thing it was hot and he had his AC on! Obviously bilge water was able to freely flow up to the front.
Reply With Quote
  #6  
Unread 01-15-2008, 10:58 PM
jasoncooperpcola's Avatar
jasoncooperpcola jasoncooperpcola is offline
God
 
Join Date: May 2007
Location: Pensacola, FL
Posts: 1,467
Send a message via Yahoo to jasoncooperpcola
Default

When we got ours last year, the forward compartment was full of water. The boat was in the water during hurricane Dennis, and has sat in a vacant lot since, it didn't sink but i found a waterline in the bathroom 4 inches off the floor. I cant remember how far off the bottom the bathroom floor is, but i think its at least a foot. The forward bilge pump was burnt out.
__________________
1983 V-20 capsized. . . . in the garage.
Reply With Quote
  #7  
Unread 01-16-2008, 11:59 PM
Skools Out's Avatar
Skools Out Skools Out is offline
God
 
Join Date: Jul 2007
Location: Graham / Emerald Isle, NC
Posts: 5,926
Default

Email Aaron at Golden in SC he can hook you up. all you need is a large clear picture to email him and he can lazer cut you a copy in any color of any decal. he cut all the ones for my 21 Cont. i had all the 225 Johnson Decals cut and the 6 more sets for my boat and he only charged $18 total with shipping for all the decals. if you get him to cut you some ask him to save the file so he cut some of us other 250 owners decals as well.

[email protected]
__________________




1978 V20 Cuddy w/ 225 Johnson. And Several other boat's
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:35 PM.


Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.