|
|
#1
|
||||
|
||||
Trim and tilt wanted for 1976 135 evinrude
Anybody have and old school motor thats for parts that has a gimble bracket on it set up for tilt and trim? I tried budget boats, them guys disappoint me everytime i go in there.
|
|
#2
10-23-2011, 08:13 PM
|
||||
|
||||
|
Quote:
Look on Craig's List...I've been keepin' an eye in there for some stuff for the '84 and I'mm seein' all kinda stuff like the T & T unit yer lookin' for...I fixin' to pick up a bimini top for 100 bucks tomorrow...
__________________
'74 V-20/ BF 150 '95 V-21/ BF 150 '84 V-20/ 200 2.4 Merc '87 V-20/'18 F150 Yamaha 
|
|
#3
10-23-2011, 08:33 PM
|
|||
|
|||
|
I have seen this posted on the Norfolk Craigslist, but I am thinking it is your listing, if not give him a call, money talks.
__________________
1973 Wellcraft V20 w/1988 Evinrude 120hp 1978 ProLine 20ft w/19?? Evinrude 150hp
|
|
#4
10-26-2011, 07:12 AM
|
||||
|
||||
|
Yea that's my post on Craigslist. I had one for the motor but my uncle snatched it from my dads house last for scrap aluminium without me knowing it. I'm a little bent about that.
|
|
#5
10-26-2011, 07:50 AM
|
||||
|
||||
|
good luck with finding any of that old trim stuff, when you do find it, it probably won't work, your best bet is a CMC tilt bracket http://cook-mfg.net/cart/index.php?m...5893853bd38284
its rated for 130 hp(propshaft), your 135 makes around 115 propshaft. Unless you have a lot of attachment to that old 135, you can find later model 88spl/90/115 V4 Johnrudes fairly cheap. The later model ones will run better on today's fuel, has a better water pump. Most of them come with power trim, lots of parts interchange as well. Keep your 135 heads and carbs if you want to make a hot rod out of it
|
|
#6
10-29-2011, 03:46 PM
|
||||
|
||||
|
Just remember that this is a low ,low budget build. I have 2 135's laying around and a 115. the 135 that im gonna put on my V has super super super low hours on it the motor is still running very very close to factory compression and I am the third owner my dad being the second owner and his best friend being the original owner. I know were this motor has been and how its been treated. It is a flawless 76' 135. I took it off the original boat it was set up with and put the motor on seadrive bracket so I had to seperatre it from its original T and T bracket. Im now removing it from the seadrive and bolting it to this V20. I might say the hell with it and put it on the manual tilt bracket my other 135 is on. and really bring it back old school
|
|
#7
10-30-2011, 08:17 AM
|
||||
|
||||
|
did you get my PM?
|
|
#8
10-31-2011, 08:48 PM
|
||||
|
||||
|
Yes I recieved your pm. thanks for the help i will call him.
|
|
#9
03-10-2012, 11:03 AM
|
||||
|
||||
|
I'm still looking for this item. I don't just need trim and tilt assembly. I need the whole bracket and trim and tilt assembly. I tried to use a 84' bracket but the pivot shaft on my 78' is 1/16 smaller. I will take just the bracket if someone has a old v-4 and then buy my own trim and tilt assembly. Thanks again
|
|
#10
03-13-2012, 07:31 AM
|
|||
|
|||
|
Some of these might work for you...
http://smd.craigslist.org/boa/2892092504.html http://smd.craigslist.org/boa/2884012519.html http://smd.craigslist.org/boa/2861039665.html
__________________
Brian
|
 |
|
|
Linear Mode
