|
|
#1
|
|||
|
|||
screw loose
1978 steplift center floor panel i have a screw that can not bet tightened and is loose the panel is coming up on that side, my question is this how do i fix it? i know the obvious solution is to use a bigger screw but i dont think that would work, should i remove the whole panel and see whats going on or is there a easier solution
thanks for any help in this matter joe
__________________
love to fish 
|
|
#2
01-26-2014, 01:26 PM
|
||||
|
||||
Quote:
YES you should..... OR if you don't want to find wood rot you could glue the panel down with 3m 5200 and glue the screw in w it n go fishing
|
|
#3
01-26-2014, 01:29 PM
|
||||
|
||||
|
I would think the hole had just been over tightened and stripped out. You could remove the panel and epoxy a strip of wood below the lip where the panel fits and use a longer screw that is able to get some bite.
__________________
1985 Wellcraft V-20, Evinrude ETEC 150: SOLD 1979 Marine Trader 44, twin Ford Lehman 120s 2006 Panga 14, Tohatsu 20
|
|
#4
01-26-2014, 03:09 PM
|
|||
|
|||
|
bradford that will work but i really ddnt want to remove the panel but i think thats the best way to go thanks
want kind of epoxy would you recommend
__________________
love to fish
|
|
#6
01-26-2014, 08:42 PM
|
||||
|
||||
|
west marine has a stainless toggle bolt for blind fastener applications
http://www.westmarine.com/webapp/wcs...5#.UuW4_H9OKSM
|
|
#7
01-26-2014, 10:26 PM
|
||||
|
||||
|
Quote:
Quote:
Last edited by smokeonthewater; 01-27-2014 at 01:34 PM.
|
|
#8
01-27-2014, 08:08 AM
|
||||
|
||||
|
You guys are overthinking this. If all you want to do is get the screw to bite and you don't want to remove the panel to see whats behind it then just take some wooden toothpicks, dunk them in Elmers Carpenters Glue (The outside type) put them still wet into the hole, break them off flush with the top, then screw the screw back in. The whole thing should take less than 3 minutes to fix.
Basically it's the same kind of fix you use to repair an oversize screw hole in a door hinge. The beauty of this repair is that you can still unscrew the screw at a later date to see what's really going on behind that panel. You can't do that if you use epoxy.
__________________
1987 V20 w/1987 150HP Yamaha on a Shoreland'r Trailer 1978 16.5 Airslot w/1996 120HP Force on a Four Winns trailer 1996 V21 w/1993 200HP Mercury on a Shoreline Trailer All towed by a 5.7L Hemi Durango. If God didn't have a purpose for us we wouldn't be here, so Live simply, Love generously, Care deeply, Speak kindly. (Leave the rest to God)  Silence, in the face of evil, is itself evil. Not to speak is to speak, not to act is to act. God will not hold us guiltless.
|
|
#9
01-27-2014, 09:28 PM
|
|||
|
|||
|
i like that one destroyer simple and yet effective and of course easy but i still like the togle bolt and other sugestions keep them coming
__________________
love to fish
|
|
#10
01-27-2014, 09:37 PM
|
||||
|
||||
|
probing with a small pick in the hole (no comments! lol) can give you an idea of the condition of the wood without removing the cover....
|
 |
|
|
Linear Mode
