|
|
#1
|
||||
|
||||
MORE 250 Sportsman Teak pictures
Here are a couple pictures of the teak i redid on my 250 Sportsman:
I made a new splashboard out of Brazilian Teak, still needs a couple more coats of teak oil. I won the stainless steel rod holders on ebay for $133.00  The original door. (Wish i had the before pictures, it was grey and rough and falling apart, literally.)  I am also currently working on a bow pulpit made out of the Brazilian Teak. I'll try to get pictures tomorrow.
__________________
1983 V-20 capsized. . . . in the garage. Last edited by jasoncooperpcola; 04-23-2008 at 10:09 PM. 
|
|
#2
04-22-2008, 07:32 AM
|
||||
|
||||
|
Look out Lumber there is a 250 hot your arse
__________________
Willy 1986 V20 Old School 1992 V20 1992 150 Yamaha 1997 HydraSport 2250 Vector 2009 17' G3 Outfitter "G Spot" http://www.youtube.com/watch?v=TDebw...eature=related "I won't be wronged, I won't be insulted and I won't be laid on a hand on. I don't do these things to others and I require the same from them" JW
|
|
#3
04-22-2008, 09:35 PM
|
||||
|
||||
|
I forgot to grab the camera on the way out so i took a picture with my phone. My pulpit is 2" thick by 15" wide by 48" long and made out of Brazilain Teak. It weighs about 60 pounds. (Not including clamps.)
 I scraped excess glue off and belt sanded it some. Tomorrow it has a date with an air tensioned drum sander (36 grit belt). 
__________________
1983 V-20 capsized. . . . in the garage.
|
|
#4
04-23-2008, 11:29 AM
|
||||
|
||||
|
You'll be able to do quadruple flips off of that platform (more like a diving board)
__________________
 1990 Hydrasports 2000cc Vector with 96 200HP Oceanrunner. Saved by grace alone, through faith alone, in Christ alone http://www.providencerpchurch.com/
|
|
#7
04-23-2008, 12:43 PM
|
||||
|
||||
|
after i get it sanded i plan to taper it then round the front. I made a mock up out of plywood. I'll take a picture of it today.
__________________
1983 V-20 capsized. . . . in the garage.
|
|
#8
04-23-2008, 09:30 PM
|
||||
|
||||
|
More pictures
My mock-up of my bow pulpit made out of plywood.
 Mock-up on the giant slab of teak:  Before and after of side rod holders:  Assortment of before and after teak stuff:  Sadly the step pad and the rod holder are gonna have to be scraped down and re teak oiled because the varnish isn't sticking good. It looks pretty but its no use if it wont stick. Before and after of step pads: 
__________________
1983 V-20 capsized. . . . in the garage.
|
|
#9
04-23-2008, 09:44 PM
|
||||
|
||||
|
Here is the beast, an 18" wide pneumaticly tensioned drum sander:
 Feeding it through:  Internal picture  Finished sanding:  Cleaning dust off: 
__________________
1983 V-20 capsized. . . . in the garage.
|
|
#10
04-23-2008, 09:48 PM
|
||||
|
||||
|
(trying to get next set of pictures on another page to make them load faster.)
__________________
1983 V-20 capsized. . . . in the garage.
|
 |
|
|
Linear Mode
