|
|
#1
|
||||
|
||||
6.5 diesel no start again
Replaced starter in January i think. Thread on here somewhere. Now it clicks and that's it. also blowwing ignore 1 fuse. I hear a thunk ever time i replace it. Sounds like it comes from starter. Any advice? Just cleaned connections and about to drop starter.
Sitting behind Papa John's now and should be working.
__________________
1983 V-20 capsized. . . . in the garage. 
|
|
#2
06-03-2013, 10:05 AM
|
||||
|
||||
|
If it just clunks then the starter solenoid is activating without kicking the voltage to the start motor. I have seen that program before.. Reman starter lasted about a week. Took the old one to the motor shop. They rebuilt it and same thing, just clicks without engaging starter motor. Crazy high compression on them motors. Not sure about blowing a fuse though..
Someone worlds smater than me are sure to be along any second..
__________________
 1996 -19' NV Flats 115 Mercury 4-stroke 1983 -20' Wellcraft Center Console 250 XS
|
|
#3
06-03-2013, 11:06 AM
|
||||
|
||||
|
Thanks for the Intro Ridge(couldn't resist)
If you hear a load clunk when you engage the starter, you may have hydraulic ed the engine. Check your oil level, see if its over full. See if you can rotate the engine over by hand, it won't be easy, you may have to use a pull bar on the crank bolt. I've seen the 6.5's stick an injector, that lets it fill teh cylinder full of fuel, you can't compress liquid. Some times if you let it sit over night, teh fuel will leak past the rings and let you start the engine, but as soon as it starts up, it will be filling the cylinder with fuel. I saw it happen in a street sweeper that stuck tow injectors at WOT, when they backed off the throttle, it was like a grenade went off, parts went everywhere, the crank shaft came out in pieces
|
|
#4
06-03-2013, 11:29 AM
|
||||
|
||||
|
Its not hydrolocked. I jumped the starter and it cranked right up. I think its the solenoid.
__________________
1983 V-20 capsized. . . . in the garage.
|
|
#5
06-03-2013, 01:38 PM
|
||||
|
||||
|
I'm not sure on your particular application but it could use a slave solenoid ahead of the start. Take a test light. Have some on turn the key, see if you have power going into the solenoid when the key is turned to start. Try shifting the gear selector to neutral and see if it makes a difference
|
|
#6
06-03-2013, 02:35 PM
|
||||
|
||||
|
Dropped it off at B&M. They just called and said it was the solenoid. Now waitingg on a ride back over there.
Another issue. I have oil all over the intake and Turbo. Looks to be from the cdR hose. The c d r was replaced two years ago. The oil is running down the exhaust manifold and frame.
__________________
1983 V-20 capsized. . . . in the garage.
|
|
#7
06-03-2013, 02:48 PM
|
||||
|
||||
|
I am wondering if the oil is coming from the Turbo...... meaning it is leaking oil and blowing it into the engine. It
__________________
1983 V-20 capsized. . . . in the garage.
|
|
#8
06-03-2013, 05:06 PM
|
||||
|
||||
|
Got the starter in. Now the dam thing constantly cranks over when ever ign 1 fuse is in. Even with the key out. So is it the key switch or the ignition switch?
__________________
1983 V-20 capsized. . . . in the garage.
|
|
#10
06-03-2013, 07:08 PM
|
||||
|
||||
|
What year truck? And which fuse exactly?(fuse panel inside the truck or under the hood).
__________________
2011 SUNDANCE B20CCR SKIFF, 2011 YAMAHA 90HP 4 STROKE, 2011 KARAVAN SINGLE AXLE ALUMINUM TRAILER, LOWRANCE ELITE-7 HDI, MINN KOTA RIPTIDE TROLLING MOTOR 2000CC HYDRA-SPORT 225+HP EVINRUDE SOLD  AND THE PINK JEEP!!!! R.I.P. http://www.wellcraftv20.com/communit...ad.php?t=11664 
|
 |
|
|
Linear Mode
