|
|
#1
|
||||
|
||||
Jack Plate or Not?
With a 29" set back bracket, would adding a jack plate make it just to far from the boat for a motor?
The reason I ask this is that I have seen a few ok deals on 30" shafts, and that would be great to get the power head up out of the water better. I see that the jack plates are a set back of at least 5" so that would be 34" So what you think??
__________________
1986 V20  Old Fishermen never die, we just SMELL that way!! 
|
|
#2
09-16-2008, 10:18 AM
|
||||
|
||||
|
I really don't know......but I figure if your steering cable is long enough it should be ok.
__________________
 1994 Wellcraft V21
|
|
#4
09-16-2008, 11:54 AM
|
||||
|
||||
|
You also need to take into account the leverage affect that the added set-back has. The furthur you go back, the more stress is being put on the transom from all that weight hanging back there. You can also look at it from the fat guy on a see saw bit. Put a fat guy on one side and a skinny guy on the other. The fat guy has to sit right next to the pivot point for the skinny guy to even have a chance of balanceing the see saw.
__________________
2011 SUNDANCE B20CCR SKIFF, 2011 YAMAHA 90HP 4 STROKE, 2011 KARAVAN SINGLE AXLE ALUMINUM TRAILER, LOWRANCE ELITE-7 HDI, MINN KOTA RIPTIDE TROLLING MOTOR 2000CC HYDRA-SPORT 225+HP EVINRUDE SOLD  AND THE PINK JEEP!!!! R.I.P. http://www.wellcraftv20.com/communit...ad.php?t=11664 
|
|
#5
09-16-2008, 12:33 PM
|
||||
|
||||
|
Thats why the question if you guys thought it was a good or bad Idea. My transom is 5" thick so the weight should be fine, but its the leverage thing?
Its all just a thought at this point.
__________________
1986 V20 Old Fishermen never die, we just SMELL that way!!
|
|
#6
09-16-2008, 12:43 PM
|
||||
|
||||
|
I would think up to a 200HP you would be fine with the added leverage, beyond that I would think the structure would sure get tested. You could always take your boat down to an aluminum welder and have hime replace the rear plate on your bracket with one 5"'s taller and weld it on there. I personally would just find a 25" shaft.
__________________
2011 SUNDANCE B20CCR SKIFF, 2011 YAMAHA 90HP 4 STROKE, 2011 KARAVAN SINGLE AXLE ALUMINUM TRAILER, LOWRANCE ELITE-7 HDI, MINN KOTA RIPTIDE TROLLING MOTOR 2000CC HYDRA-SPORT 225+HP EVINRUDE SOLD AND THE PINK JEEP!!!! R.I.P. http://www.wellcraftv20.com/communit...ad.php?t=11664
|
|
#7
09-16-2008, 12:49 PM
|
||||
|
||||
|
Most likely I will get a 25 as there many more of them around. But I have seen a couple of 30's and just got to thinking.
Heck I have got a total of 1 1/2 hour on the 175, I just lowered it a hole as it was to high, and I just changed the prop from 17 to a 15 for a better out the hole and lower the RPM from 6K It might be just fine? I got it to 30 knots, and cruz mid 20's fine, but you can tell itys the smallest HP you want on that boat! Thanks!!
__________________
1986 V20 Old Fishermen never die, we just SMELL that way!!
|
|
#8
09-16-2008, 02:50 PM
|
||||
|
||||
|
hey maco, you get on one side of the see saw and i'll get on the other. (guess who is the fat guy).
__________________
hammer aint. stinkpot aint. sawdust aint. rainbow aint. maco sure as sh!t aint. randle? ha ha ha. 
|
|
#9
02-18-2009, 03:13 PM
|
|||
|
|||
|
mj cmc makes some extensions plates that are made to run a 5" taller motor on a transom with out giving it more set back, we have installed several and they work really well.
|
|
#10
02-18-2009, 03:14 PM
|
|||
|
|||
|
|
 |
|
|
Linear Mode
