Forum: Performance
06-15-2012, 04:35 PM
|
|
Replies: 3
Views: 321
Gas line size
Hey guys i had a thought about my RPM problem, ( only getting 4500 ) I have been through all the checks in the past 1-1/2 years, when I did my new transom ( 2 Yrs. ago ) I replaced all fuel lines...
|
|
Forum: Performance
06-11-2012, 06:36 AM
|
|
Replies: 6
Views: 394
|
|
Forum: Performance
06-09-2012, 03:06 PM
|
|
Replies: 6
Views: 394
|
|
Forum: Performance
06-09-2012, 07:30 AM
|
|
Replies: 6
Views: 394
Testing tach
If I just disconnected wires from back of existing tach and rewired them to a different tach and had someone just hold it while running, do you think this will be a good test to se if my tach is...
|
|
Forum: Performance
06-04-2012, 09:45 AM
|
|
Replies: 20
Views: 1,281
I raised the engine 2 holes, took it out and it...
I raised the engine 2 holes, took it out and it seems smoother and the wake is now clean and no spray, I heard a little loss of bite around a hard turn in the chop, but I was running it pretty hard,...
|
|
Forum: Performance
05-29-2012, 05:39 PM
|
|
Replies: 16
Views: 732
|
|
Forum: Performance
05-29-2012, 05:09 PM
|
|
Replies: 16
Views: 732
|
|
Forum: Performance
05-29-2012, 02:31 PM
|
|
Replies: 16
Views: 732
Just bury the shifter forward, that would be...
Just bury the shifter forward, that would be putting it in gear, is this OK. My shifter is not the kind you can pull out and rev in nuetral. I can't rev my engine in nuetral, only a little with the...
|
|
Forum: Performance
05-29-2012, 02:28 PM
|
|
Replies: 16
Views: 732
|
|
Forum: Performance
05-29-2012, 01:50 PM
|
|
Replies: 16
Views: 732
|
|
Forum: Performance
05-29-2012, 01:29 PM
|
|
Replies: 16
Views: 732
Compression numbers ?
I took some numbers today with a known good tester. My engine was rebuilt as some of you have seen my story in the past. Running good just wanted to know what you thought of these #'s
Cold with...
|
|
Forum: Performance
05-27-2012, 08:41 AM
|
|
Replies: 1
Views: 233
How mant poles ?
How mant poles does a 1994 150 HP Ocean Runner alternator have ? ( trying to verify my Tach is set right )
|
|
Forum: Repairs
03-06-2012, 06:34 PM
|
|
Replies: 19
Views: 1,081
|
|
Forum: Performance
11-13-2011, 08:32 AM
|
|
Replies: 20
Views: 1,281
|
|
Forum: Performance
11-13-2011, 08:16 AM
|
|
Replies: 20
Views: 1,281
At the botom of the engine bracket there are 6...
At the botom of the engine bracket there are 6 holes ( two rows of three ) on approx. a 45 degree angle, there is a stainless rod ( about 5/8" Diameter ) going through one of the holes to the other...
|
|
Forum: Performance
11-12-2011, 04:38 PM
|
|
Replies: 20
Views: 1,281
Well pulled the boat for the season today, upon...
Well pulled the boat for the season today, upon inspection I found the cause of the rattle. A while ago I had a rattle and found out it was my trim rod rattling when I went over 2000 RPM's because...
|
|
Forum: Performance
11-09-2011, 10:43 PM
|
|
Replies: 20
Views: 1,281
Thanks, I will try these changes, I'll check my...
Thanks, I will try these changes, I'll check my lower unit oil, but I never had a problem with leaking, the reason I am wondering about the lower unit is that when I got this motor the mechanic told...
|
|
Forum: Performance
11-09-2011, 05:15 PM
|
|
Replies: 20
Views: 1,281
|
|
Forum: Performance
11-08-2011, 08:03 PM
|
|
Replies: 20
Views: 1,281
|
|
Forum: Performance
10-12-2011, 02:18 PM
|
|
Replies: 20
Views: 1,281
|
|
Forum: Performance
10-11-2011, 08:49 PM
|
|
Replies: 20
Views: 1,281
engine height
I think my motor is too low, tons of spray when underway, Engine is mounted through the top hole 25" shaft, cav plate is under water when going fast, I can't see it. Here are some pics when i am...
|
|
Forum: Performance
10-08-2011, 09:06 AM
|
|
Replies: 8
Views: 440
Thanks for that response, yeah adjusting the...
Thanks for that response, yeah adjusting the cable makes sense to me being that when my old mechanic had it for a repair the prop was not turning when in nuetral when I went to pick the boat up from...
|
|
Forum: Performance
10-06-2011, 08:10 PM
|
|
Replies: 8
Views: 440
low idle adjustment
I have a 1994 150 HP V6 looper, she runs good but when in gear it seems it seems the rpm's are on the low side (400) once in a while when approaching a dock switching between gears it stalls. How do...
|
|
Forum: Performance
09-26-2011, 03:38 PM
|
|
Replies: 13
Views: 883
You guys are scaring me, but I am not surprised...
You guys are scaring me, but I am not surprised with this guy. If it means anything, I did the test on a cold engine, only taking one plug out at a time, I did the test when I was troubleshooting my...
|
|
Forum: Performance
09-25-2011, 02:10 PM
|
|
Replies: 13
Views: 883
Even if my tach is not accurate shouldn't I be...
Even if my tach is not accurate shouldn't I be going 40-45 MPH at full RPM with my setup. These are the numbers I have seen with similiar setups on this forum. I am running on all cylinders I just...
|
