Forum: Boats For Sale or Wanted
07-24-2008, 10:30 AM
|
|
Replies: 2
Views: 459
|
|
Forum: Boats For Sale or Wanted
07-21-2008, 12:14 AM
|
|
Replies: 2
Views: 459
Wellcraft Fisherman V20 Center Console
Hull is 1982 Model V-20 CC Fisherman
1990 Johnson 200
12 rod holders
Garmin 498 GPS/Sounder
Standard Horizon VHF Works well and antenna is good.
Seawater wash down, 2 1100 GPH bilge pumps,...
|
|
Forum: Performance
11-27-2007, 04:24 PM
|
|
Replies: 16
Views: 595
Re: Trolling motor
Image was from old West Virginia home, boat now resides 45 minutes from the Pamilco and 100 miles from Morehead City. Recent results from smaller boat with trolling motor below, I recently had back...
|
|
Forum: Performance
11-26-2007, 05:44 AM
|
|
Replies: 16
Views: 595
Re: Trolling motor
Thanx for all the help guys. What length shaft are you using on yours reelapeelin ? Probably going to order this week from bass Pro. Looks like a 52" would be marginal, but a 60 " shaft would be long...
|
|
Forum: Performance
11-18-2007, 02:04 AM
|
|
Replies: 16
Views: 595
Re: Trolling motor
Think I want to stick to bow mounted if possible, have bad back and like to cast from pedestal. I have *a ladder on back of my T-top that interferes with casting.
...
|
|
Forum: Performance
11-16-2007, 10:30 PM
|
|
Replies: 16
Views: 595
Trolling motor
I am tempted to add a electric trolling motor to my V-20 CC for river, creek and sound *fishing. Probably want at least 100 lbs of thrust. Primary use for my boat is trolling for Kings, Spanish and...
|
|
Forum: Boats For Sale or Wanted
10-28-2007, 09:23 PM
|
|
Replies: 11
Views: 369
Re: VRO Tank Wanted
Found one on ebay. See link below for reliability of VRO.
http://continuouswave.com/whaler/reference/VRO.html
|
|
Forum: Boats For Sale or Wanted
10-26-2007, 10:00 PM
|
|
Replies: 11
Views: 369
VRO Tank Wanted
VRO tank wanted, going to convert back to VRO. 1.8 Gallon tank prefered. Will pay reasonable cost for used unit, they are going for $10-$40 used on ebay.
|
|
Forum: Repairs
10-13-2007, 06:11 PM
|
|
Replies: 5
Views: 251
Re: Johnson Tilt & Trim
I used wrench below. I heated the mid section on both
sides and sprayed PB Blaster while it was hot. Had to hit it from both sides, would move a little then I would hit it from the opposite side....
|
|
Forum: Repairs
10-13-2007, 06:02 PM
|
|
Replies: 13
Views: 332
|
|
Forum: Repairs
10-08-2007, 03:08 PM
|
|
Replies: 5
Views: 251
Re: Johnson Tilt & Trim
got it out !!!! Used air hammer. Now can not get cap off cylinder. Got to get better spanner wrench.
|
|
Forum: Repairs
10-07-2007, 10:04 PM
|
|
Replies: 5
Views: 251
Johnson Tilt & Trim
Need to replace seal in center tilt cylinder on 200 HP 1990 Johnson. How in the heck do you drive the tilt cylinder pin out? I believe I have reached a neutral position so shaft is not loaded but the...
|
|
Forum: Boats For Sale or Wanted
10-07-2007, 01:02 AM
|
|
Replies: 8
Views: 242
|
|
Forum: Boats For Sale or Wanted
10-02-2007, 06:14 PM
|
|
Replies: 6
Views: 245
|
|
Forum: Boats For Sale or Wanted
10-02-2007, 03:37 PM
|
|
Replies: 6
Views: 245
Re: Evinrude / Johnson Stator Wanted
I'm in Greenville/Farmville, will head to the beach this weekend if the wind finally stops blowing. ;D
Are you saying that any Non DFI 200 HP up stator will work if I change the connectors ?
|
|
Forum: Boats For Sale or Wanted
10-02-2007, 08:18 AM
|
|
Replies: 6
Views: 245
|
