Wellcraft V20 Community

Wellcraft V20 Community (https://forums.wmpdevserver1.com/community/index.php)

- Modifications (https://forums.wmpdevserver1.com/community/forumdisplay.php?f=13)

- - Rod boxes (https://forums.wmpdevserver1.com/community/showthread.php?t=4990)

The previous owner of my V built a replacement rod box on the starboard side because the plastic one pooped out. He did a pretty nice job other than selecting regular screws instead of stainless.

I replaced the screws, well most of them (the batt. on my drill gave out).

He had "Rod Savers" in place of rod racks, I may go back with that or figure something else out. The ones that were here are broken.

http://i145.photobucket.com/albums/r...101_0098-2.jpg

http://i145.photobucket.com/albums/r...101_0099-2.jpg

http://i145.photobucket.com/albums/r...101_0100-2.jpg

http://i145.photobucket.com/albums/r...101_0101-1.jpg

http://i145.photobucket.com/albums/r...101_0102-2.jpg

Do I see the stringer killer present in your boat Randleman :o? It's also known as foam. Just ask Jeffx or me what we think about the s$#%. It will hold moisture and if your strigers are not completely sealed, and they probably are not, the rot monster will come visiting. :( :'(

randleman, I'll post some pics of what I'm doing wioth my rod boxes, so far it hasn't cost mush and should work out better, i was waiting to finsh wiht them before I posted the pics, but it looks like your in the same delima i was, so maybe it will help, I'll post pics tonight

Cover up that hole with a sheet of starboard and mount tank racks, so I can do some NC wreck diving. ;D

Hammer,

We can just stack em in the cabin like cord wood, come on down. Hey, would you put fish on my hooks while your down there?

Quote:

Hey, would you put fish on my hooks while your down there?

....and mine ??? ;D

In the old 75 thats were the 20 gal gas tanks are, no rod boxes!!

allright randleman, this is what i did.
I removed the existing rod boxes
http://i112.photobucket.com/albums/n...brodholder.jpg

fit a couple of spacer blocks

http://i112.photobucket.com/albums/n...holders008.jpg

[img]
http://i112.photobucket.com/albums/n175/spareparts_photos/rodholders007.jpg[/img]

i ran some 3" pvc thru the spacers for cable runs

http://i112.photobucket.com/albums/n...holders010.jpg

http://i112.photobucket.com/albums/n...holders009.jpg

then i cut some 2X6 for a shelf, installed teh new shelf with construction adhesive, glassed over the top, this really stiffened up the hull sides

http://i112.photobucket.com/albums/n...holders012.jpg

http://i112.photobucket.com/albums/n...holders005.jpg

http://i112.photobucket.com/albums/n...holders004.jpg

next to come is carpet and rod holders, I'll post some pics when its done. I got the idea from an older Formula, that shelf is nice, you can throw junk in there and it doesn't fall out, I'm going to use the original trim for now, but plan to make new trim later

Hey Spareparts,

I have the rod boxes out of my V for teak refinishing, box glass reinforcement, box refinish. I like the wiring tubes and will incorporate (copy) that idea on my boat if you don't mind. In your last picture, you have a track running fore and aft just below the gunnels. I have the same track on my V but don't know what it is used for. Do you know what it is for?

Geek

sliding camper top support, long since been mia on my boat, will not reappear