Wellcraft V20 Community

Wellcraft V20 Community (https://forums.wmpdevserver1.com/community/index.php)
-   General (https://forums.wmpdevserver1.com/community/forumdisplay.php?f=10)
-   -   How long to flush? (https://forums.wmpdevserver1.com/community/showthread.php?t=3957)

BassOMaticII 01-05-2006 04:42 AM

How long to flush?
 
What is considered an ample amount of time to flush a motor after use in salt water? Does the size and type of engine matter ie: outboard vs I/O, V8 vs V4...
Do any of you use the salt cleansing agents if the boat is used weekly?
I have a GM 5.7L and an OMC 800. I have been flushing for about 10 minutes which seems like an eternity.

Thanks in advance,

BassOMaticII

reelapeelin 01-05-2006 09:10 AM

Re: How long to flush?
 
BOM...I time 5 mins on mine, which seems an eternity to me...lotta H2o through in 5 mins...if that don't get it, it ain't gonna be got...JMHO ;)

There's also the saltwater flush...don't think necessary every time, but good idea every third to fifth time out...

Skools Out 01-05-2006 09:34 AM

Re: How long to flush?
 
i taste the water coming out the exhaust after couple mins and if it taste salty i check it again a couple more mins later then usually good so then i run it after no salt taste couple more mins. but the last 2 min after the salt taste is gone i rev the motor up and hold it around 3500 then pop it up a couple times to get the salt out of the high rpm water over flow lines. then shut her down.

phester 01-05-2006 10:51 AM

Re: How long to flush?
 
skools,that's exactly what I do

Mulv80 01-05-2006 10:59 AM

Re: How long to flush?
 
WOW, 3500 rpm's with no load on muffs

Franco 01-05-2006 11:08 AM

Re: How long to flush?
 
I LIKE MY YAMMIE - DIRECT CONNECTION AND YOU DON'T HAVE TO RUN THE MOTOR - 5 MINUTES AND DONE

Skools Out 01-05-2006 12:49 PM

Re: How long to flush?
 
yeah 3500 that's the only way you'll get your overflow lines and areas in the motor flushed, if you go to some shops out back they turn motors up in the 4500 to 5000 range on muffs. Scares me to go there though to hold there but setting timing advance requires getting it to 4500 on some motor.

Mulv80 01-05-2006 01:44 PM

Re: How long to flush?
 
I always heard that you run the risk of having a motor "run away" when you run up the rpms without a load. *I've heard stories about motors that continued to rev even after they were shut down when they "run away." scary

macojoe 01-05-2006 02:11 PM

Re: How long to flush?
 
I just run it till it feels good!!

I start the engin as start to clean all the fishing stuff out from a day of fishing, It may run 10 min it may run 20 min?
But it works for me!

Skools Out 01-05-2006 03:17 PM

Re: How long to flush?
 
yeah if they run away it was due to running to lean with stopped up jets in the carbs the more cylinders the less likely it will happen. I've had jet ski's do that and to stop it just choke it and the fuel kills it on a dime.


All times are GMT -5. The time now is 08:18 PM.

Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.