Upgrades to the V
 

Well, I decided to replace some of the wood on the V, I am getting tired of the Teak upkeep.

I found Boat Outfitters in my backyard and picked up a 4 x 8 x3/4 sheet of King Starboard for a whopping out-the-door price of $512.57!!!

Using my table saw and router I am carving up some fine-looking pieces.

https://photos.app.goo.gl/vyEmCyiJHbX7drQP8

Very Nice!!!:love:

:clap:

Nice! You've got real talent!

I've never used a router before. I bought one about 10 years ago... and I bought a set of router bits too... then, after a year or two when I went to use it, I discovered that my router only holds 1/4" bits, but the set of bits I bought are all 1/2" -- Go figure! I know that having the tool doesn't mean that I know how to use it.... but I was hoping to learn. C'est la vie.... maybe one day!

I really like our work. nice job!

What are the sections for? I can see the windlass ones, but none of the doors installed.



They look good!


I had to make a cover plate for my rigging tube hole and and used some left over starboard. I chose the same blade you did, my bevel looks exactly like yours...lol


Thanks for sharing.

Great job but how is the pulpit holding up? Is it strong? The panels I don't know what they are for but they look great, I thought you were talking about the trim on your boat and the cabin door too.

Hey PJ - it kills me for a guy to have a tool he wants to use but can’t. Are you sure it only takes 1/4” shank bits - there’s often an adapter that slips into the 1/2” chuck which can be removed. If not, watch for a sale on bits and buy one, probably a 1/4” radius round over and have some fun easing the edges on projects you make.

Not hijacking the thread - nice work on the starboard pieces. To avoid the little ridge, I always keep a scrap of material to test the cut. Another thing that REALLY improved my edge routing work was to get a router lift - made a router table out of the extension on my table saw. It makes managing the material much easier and more consistent for this kind of work.

You’re going the right direction - several years ago, I replaced some of my wood with new wood - I wish I’d done what you’re doing.

Looking forward to pictures of the completed project.

I just saw your reply, @scook. Thank you for the info and advice. I'll check my router, and also look for the bit you mentioned on sale... I didn't know what bits would be useful, which is why I purchased a set with about a dozen bits.

@O.P. I really do like your work. Post up more pics after you've installed them. My V20 has teak, and while gorgeous, it -- of course -- will require upkeep too.

Used router on Ipe for bow pulpit... also got cutting board to use vs star board...
 

So, I know it's almost a year later... but I thought i'd try to revive this thread.

I bought a set of inexpensive router bits, and used them on some Brazilian hard wood called IPE to make my own bow pulpit.

Attachment 8315

I used the router, and then used "Ipe Oil" when I was done. All of the cut edges have to sealed with this special wax, otherwise the wood dries un evenly and you cracking or splintering.
Attachment 8314
The first version extended past the bow almost 3 feet. Although I used large pieces of Ipe ... about 1 ft long, in the cabin under the deck along with large fender washers to spread out the load, I still felt that the pulpit was too long and put too much strain on the deck... I could see it flexing too easily... and the wood flexed more than I liked... so I cut it down to make it shorter.

At some point I'll go back with the router to clean up the end I cut.

Well... here's a picture of how it looks so far....
Attachment 8313

I also found what I think will be a cheaper source to obtain medium sizes of HDPE (High Density Poly Ethelyene)...
:haha:Attachment 8316

I think that's the same material that Star Board is.... but if anyone knows of important differences... like (maybe treatment for enhanced UV resistance) please enlighten me before I go too far down this path!

You'll start to see more posts from me, as I'm really kicking this Pandemic V20 project into extra high gear!

P.S. -- Not trying to steal the O.P.'s thread. Since it went dormant, I thought this would be a good place to post about my work with trim and also starboard / starboard alternatives. If that's a bad idea.... please let me know, and I'll start my own thread or post everything under that "build thread" that I started and never got any photos in.

-Philip