Wellcraft V20 Community
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

Wellcraft V20 Community (https://forums.wmpdevserver1.com/community/index.php)
-   Repairs (https://forums.wmpdevserver1.com/community/forumdisplay.php?f=16)
-   -   Throttle/Shift Cables (https://forums.wmpdevserver1.com/community/showthread.php?t=13879)

Blue_Runner 04-20-2010 08:07 AM
Throttle/Shift Cables
 
My throttle cable has a cracked shroud right where it enters the rubber grommet on the front of motor. It is starting to get rusty causing idle & shifting problems. It is getting bound at the rusty spot not allowing the RPM's to adjust down to idle after coming off a plane or just shifting out of gear into neutral.

My question is where should I get the replacement cables? And what brand is best?

The motor is an '04 Yamaha 150 2-stroke. It has the Yamaha premium flush side mount boat control, mfg. part # 6X0-48206-12-00.

Thanks!
Blue

reelapeelin 04-20-2010 03:02 PM
Quote:
Originally Posted by Blue_Runner (Post 156685)
My throttle cable has a cracked shroud right where it enters the rubber grommet on the front of motor. It is starting to get rusty causing idle & shifting problems. It is getting bound at the rusty spot not allowing the RPM's to adjust down to idle after coming off a plane or just shifting out of gear into neutral.

My question is where should I get the replacement cables? And what brand is best?

The motor is an '04 Yamaha 150 2-stroke. It has the Yamaha premium flush side mount boat control, mfg. part # 6X0-48206-12-00.

Thanks!
Blue
I ain't all hung up on replacing all w/factory parts...but in this case, why not get 'em from a Yammy dealer...seein as how it's Yammy on both ends... :hi:

tsubaki 04-20-2010 03:06 PM
Blue, I hope I'm not over simplifying stuff. Not sure about the Yamaha but the cables are about as common as spark plugs.
Our local boat places, hardware stores even Bass Pro (online) carries them.
Usually we get Teleflex stuff, they have a 3300 series (universal) made for Yamaha and others. See if the ends are the same as yours.

THEFERMANATOR 04-20-2010 03:23 PM
TELEFLEX makes most of the OE cables for the manufacturers to begin with. WEST MARINE, EBAY, and just about any boat parts store can order them for you. They most likely make them with factory ends and would be a direct swap.

Blue_Runner 04-20-2010 03:55 PM
10-4....I've been looking around. Just wanted to ask before I pulled the trigger then you guys say, "why the heck didn't you just buy such and such" :hi:

Thanks fellas.

spareparts 04-20-2010 05:47 PM
go ahead and splurge and get the "supreme cables". I've used the Uflex cables, they aren't as nice as the teleflex supreme, but they sure cost a lot less, and they get the job done.

reelapeelin 04-21-2010 04:02 AM
Like Spare said...Go w/the SUPREMES!!...:clap:...don't wanna be scrimpin about that Purdy Lil 21 :love:

Blue_Runner 04-21-2010 07:38 AM
Quote:
go ahead and splurge and get the "supreme cables". I've used the Uflex cables, they aren't as nice as the teleflex supreme, but they sure cost a lot less, and they get the job done.
See? This is why I ask....now I'm E-D-U-M-A-C-A-T-E-D!

So should I pull the old cables to get the length or just measure using the formula? Probably doesn't make a whole heck of a lot of difference either way huh?

bradford 04-21-2010 04:42 PM
Quote:
Originally Posted by Blue_Runner (Post 156740)
See? This is why I ask....now I'm E-D-U-M-A-C-A-T-E-D!

So should I pull the old cables to get the length or just measure using the formula? Probably doesn't make a whole heck of a lot of difference either way huh?

I'd pull the old ones or try to get a part # to cross reference the length. Don't want your cable to be an inch too short if ya know what I mean.

Blue_Runner 04-22-2010 08:01 AM
Zackly Bradford!


All times are GMT -5. The time now is 06:22 AM.
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.